Hatco DL-400 Installation And Operating Manual Download Page 16 | Manualshive

Page: 16 / 20

background image

Form No. DHLM-1207

14

TROUBLESHOOTING GUIDE

SYMPTOM

PROBABLE CAUSE

CORRECTIVE ACTION

Heat is excessive.

Control switches burn-out
rapidly.

Unit mounted too close to
target area.

Check to see that installation is within
specifications for type/model. Increase
mounting height if too close.

Voltage supply too high.

Check power supply to unit, making sure
it matches rating on unit. If power supply
is incorrect, change to match rating.

Switches used are not Hatco
supplied.

Genuine Hatco components are specified
to operate safely and properly in the
environment in which they are used.
Replace switches with Genuine Hatco
Parts if switches are aftermarket or
generic.

«
...
14
15
16
17
18
...
»

Summary of Contents for DL-400





















Reviews:

No comments

Related manuals for DL-400

Brand: Lasko Pages: 8

Brand: Vanguard Pages: 36

Brand: Jata Pages: 32

Brand: Jata Pages: 28

Brand: Jata Pages: 28

Brand: DeLonghi Pages: 4

Racor RK15438-01

Brand: Parker Pages: 8

Brand: Dura Heat Pages: 22

Brand: ARDES Pages: 28

Brand: Payne Pages: 4

FIGHTER 2010 Series

Brand: Nibe Pages: 36

Brand: Jocel Pages: 34

Brand: FACTO Pages: 21

Brand: Western Shelter Systems Pages: 2

Brand: VEAB Pages: 10

Conservationist PXHS

Brand: A.O. Smith Pages: 20

Kitchen Flower 76501

Brand: Yarden Pages: 22

Brand: T Therm Geo Pages: 53

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands