![background image](http://html1.mh-extra.com/html/hatco/cwbr-series/cwbr-series_installation-and-operating-manual_2107084011.webp)
Form No. CWBRM-0220
11
English
Model
Width
(A)
Depth
(B)
CWBR-S1
CWBX-S1
25-1/4
″ –
26-1/16
″
(641 – 662 mm)
17-1/16
″–
17-15/16
″
(433–456 mm)
CWBR-S2
CWBX-S2
46-1/4
″ –
47-15/16
″
(1175 – 1196 mm)
17-1/16
″ –
17-15/16
″
(433 – 456 mm)
CWBR-S3
CWBX-S3
67-5/16
″ –
68-1/8
″
(1710 – 1731 mm)
17-1/16
″ –
17-15/16
″
(433 – 456 mm)
CWBR-S4
CWBX-S4
88-3/8
″ –
89-1/4
″
(2245 – 2266 mm)
17-1/16
″ –
17-15/16
″
(433 – 456 mm)
Model
Width
(A)
Depth
(B)
CWBR-1
CWBX-1
17-1/8
″ –
18
″
(435 – 457 mm)
25-3/16
″ –
26
″
(640 – 660 mm)
CWBR-2
CWBX-2
30-1/8
″ –
31
″
(765 – 787 mm)
25-3/16
″ –
26
″
(640 – 660 mm)
CWBR-3
CWBX-3
43-1/8
″ –
44
″
(1095 – 1118 mm)
25-3/16
″ –
26
″
(640 – 660 mm)
CWBR-4
CWBX-4
56-1/8
″ –
57
″
(1425 – 1448 mm)
25-3/16
″ –
26
″
(640 – 660 mm)
CWBR-5
CWBX-5
69-1/8
″ –
70
″
(1756 – 1778 mm)
25-3/16
″ –
26
″
(640 – 660 mm)
CWBR-6
CWBX-6
82-1/8
″ –
83
″
(2086 – 2108 mm)
25-3/16
″ –
26
″
(640 – 660 mm)
INSTALLATION
B
A
Countertop Cutout Dimensions
For CWBX and CWBX-S Models:
a. Connect the on-site power supply through the power
input knockout to the POWER IN terminal block.
b. Connect power from the POWER OUT terminal block,
through the power output knockout, to the solenoid
valve on the refrigerated well.
c. Connect the temperature probe wire connector from
the well to the probe wire connector from the digital
temperature controller.
Solenoid Valve
Power Input
Temperature probe installed here.
Wire from probe connects to control panel
(same for CWBR Models).
CWBX Model Electrical Connections
Installing the Control Box Remotely
Use the following procedure to install the control box remotely.
WARNING
Control Box must be mounted in a vertical surface.
Mounting Control Box in a horizontal surface may result
in the collection of liquids and lead to electric shock.
1. Cut and drill the appropriate holes in the mounting
surface. Refer to the “Control Box Cutout and Screw Hole
Dimensions” chart for the cutout dimensions.
2. Remove the four trim cover screws from the control box
and remove the trim cover.
3. Position the control box into the cutout opening through the
backside.
4. Fasten the control box to the vertical surface using four
screws (not supplied).
5. Apply a 1/4″ (6 mm) bead of NSF-approved silicone sealant
where the trim cover will contact the cabinet surface. Refer
to the “Control Box Cutout and Screw Hole Dimensions”
illustration for more information.
6. Reinstall the trim cover on the control box and secure in
position using the four trim cover screws. Make sure to
embed the trim cover edge into the silicone.
7/16″
(11 mm)
3/8″
(9 mm)
Silicone Sealant
5-5/8″
(143 mm)
7-7/16″
(189 mm)
7-3/4″
(196 mm)
3-1/2″
(89 mm)
1-1/16″
(27 mm)
Control Box Cutout and Screw Hole Dimensions
NOTE: Make sure the width of the Control Box cutout does not
exceed the above dimension.