background image

SPECIFICATIONS

TRANSMITTER SECTION

a.  RF Output Power
b.  Freq. Deviation (@1 KHz)
c.  Audio Freq. Response

4 watts (MPT-1320)
±2.5 KHz max.
+2
-5
at 0.3-3.0 Khz pre-emphasise
less than 50nw

dB per 6dB/OCT

d.  Spurious Emission
   80 - 86 Mhz
   87.5 -118 Mhz
   135-136 Mhz
   174-230 Mhz
   470 - 862 Mhz
   Other Freq.                                             Less than 0.25uW
e.  Adjacent Channel Power                      less than 10uW

POWER SUPPLY

AC OPERATION

For your own safety read following instruction carefully before attempting to connect
this unit to the mains.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:
      

Green-and-yellow     

:   Earth

      

Blue                         :   Neutral

      Brown                      :   Live
As the colours of the wires in the mains lead of this apparatus may not correspond with
the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured green-and-yellow must be connected to the terminal in the
plug which is marked by the letter E or by the safety earth symbol      or coloured green or
green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with
the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked
with the letter L or coloured red.
If a 13A plug is used, fit a 3A Fuse. If any other plug is used, protect with a 5A fuse in
the plug, adaptor, or at the distribution board.

CAUTION:     

TO PREVENT ELECTRIC SHOCK DISCONNECT FROM THE MAINS BEFORE

                       REMOVING COVER. NO USER-SERVICEABLE PARTS INSIDE.
                       REFER SERVICING TO QUALIFIED SERVICE 

PERSONNEL

SAFETY PRECAUTION:

THIS   EQUIPMENT  MUST BE  DISCONNECTED  FROM THE MAINS WHEN NOT IN USE.
*DO NOT ALLOW THIS UNIT TO BE EXPOSED TO RAIN OR MOISTURE.

WARNING:    

THIS APPARATUS MUST BE EARTHED.

- 7 -

Summary of Contents for H407
















Reviews: