background image

 MACH

®

  Series

 

Gas-Fired Boiler 

Appendix 

 

47 

7    LIMITED WARRANTY 

P-K MACH

®

 Series Boiler 

LIMITED WARRANTY 

 

 

LIMITED WARRANTY 
Subject to the terms and conditions herein, Patterson-Kelley Co., Seller, warrants to the original owner at the original installation site that products 
manufactured by Seller will be free from defects in materials and workmanship for a period of one (1) year from date of start up (the "Warranty 
Period"), provided that start up is completed within six months from the date of shipment. The heat exchanger and burner will be warranted for a 
period of (5) five years from the date of shipment (the "Warranty Period").   
 
REMEDY 
The sole remedy of this warranty is expressly limited to the repair or replacement of any part found to be defective under conditions of normal use 
within the Warranty Period.  Installation is not included. 
 

Warranty - The owner must notify the original installer of the Product and Seller (Attention: Patterson-Kelley Co., P.O. Box 458, East Stroudsburg, 
PA 18301), in writing, within the Warranty Period, providing a detailed description of all claimed defects.  Transportation to the factory or other 
designated facility for repairs of any products or items alleged defective shall, in all events, be the responsibility and at the cost of the owner. 

 
EXCLUSIONS 
Seller shall have no liability for and this warranty does not cover: 

A.  Incidental, special or consequential damages, such as loss of the use of products, facilities or production, inconvenience, loss of time or 

labor expense involved in repairing or replacing the alleged defective Product.  

B.  The performance of any Product under conditions varying materially from those under which such Product is usually tested under 

industry standards at of the time of shipment 

C.  Any damage to the Product due to abrasion, erosion, deterioration, abnormal temperatures or the influence of foreign matter or energy. 
D.  The design or operation of owner's plant or equipment or of any facility or system of which any Product may be made a part. 

 

E.     The suitability of any Product for any particular application. 
 F.  Any failure resulting from misuse, modification not authorized by Seller in writing, improper installation or lack of or improper 

maintenance.                                                                                                                           

G.  Equipment furnished by the owner, either mounted or unmounted, or when contracted for by the owner to be installed or handled. 
H.  Leakage or other malfunction caused by: 

1. Defective installations in general and specifically, any installation which is made: 

a. 

in violation of applicable state or local plumbing housing or building codes, 

b. 

contrary to the written instructions furnished with the unit 

 

2. Adverse local conditions in general and, specifically, sediment or lime precipitation in the tubes and/or headers or corrosive 

elements in the atmosphere. 

3. Misuse in general and, specifically, operation and maintenance contrary to the written instructions furnished with the unit, 

disconnection, alteration or addition of components or apparatus, not approved by Seller, operation with fuels or settings other 
than those set forth on the rating plate or accidental or exterior damage. 

I. 

Production of noise, odors, discoloration or rusty water. 

J. 

Damage to surrounding area or property caused by leakage or malfunction. 

K.  Costs associated with the replacement and/or repair of the unit including: any freight, shipping or delivery charges, any removal, 

installation or reinstallation charges, any material and/or permits required for installation, reinstallation or repair, charges to return the 
boiler and or components.  Seller's liability under this warranty shall not in any case exceed the amount paid for the Product found to be 
defective. 

 

THIRD-PARTY WARRANTIES 
For goods or components not manufactured by Seller, the warranty obligations of Seller shall, in all respects, conform and be limited to one (1) year 
from the date of shipment. 
 
SEVERABILITY 
To the extent that any provision of this warranty would be void or prohibited under applicable law, such provisions shall be limited in effect to the 
minimum extent necessary to render the remaining provisions hereof enforceable. 
 
NO OTHER WARRANTIES 
Seller makes no implied warranty of merchantability or fitness for a particular purpose or other warranties with respect to any products or services 
except as expressly set forth in this limited warranty. 
 

Note: Rev. January 1, 2006

 

Summary of Contents for Patterson-Kelley MACH Series




















































Reviews: