![background image](http://html1.mh-extra.com/html/harry-taylor/ht2000/ht2000_installation-and-servicing-manual_4010753056.webp)
56
Because of continuous product innovation,
Harry Taylor Heaters Limited reserve the right to
Harry Taylor of Ashton Ltd.
Unit 1-3 Guildebridge Trading Estate,
South Street, Ashton-Under-Lyne.
OL7 0HU United Kingdom.
Telephone +44 (0) 161 3084550
Facsimile +44 (0) 161 3084551
Email
Website www.harrytaylor.co.uk
10.1 Commissioning and hand over
Warning
As part of the commissioning programme,
the commissioning engineer must go
through the following with the operator.
(i) Lighting, shutdown, and operational
information.
(ii) Safety features, data plate, and labelling.
(iii) The requirement for regular inspection -
especially if the heater is within a more
demanding environment - and the need for
regular servicing, carried out by competent
and qualified engineers.
Caution
After approximately 100 hours of running,
the tension on the fan belts must be
checked to ensure that it is correct, and that
the belts have not stretched.
It is strongly advised that this is undertaken
by the commissioning engineer, and not the
operator
10.2 Servicing
Warning
Servicing must be carried out on a regular
basis, the maximum interval between
services being one year.
It is a requirement that only suitably qualified
and competent persons are allowed to
undertake the servicing.
Harry Taylor advise that the planned service
schedule as detailed in section 5.1 of the
Installation, Commissioning and Servicing
Manual is adopted by the user.
Further details are available from either
Harry Taylor or from the commissioning
engineer.
10.3 Start Up Procedure
(a) Enable burner via controller by selecting
‘Heat’ (Relay 2); ‘Heat On’; ‘Heat/Auto’.*
(* dependent on control type supplied. Refer
to individual controller operating manual.)
(b) Burner will fire and establish within
60seconds.
(c) As temperature of heater increases, fan
will operate.
10.4 Stop procedure
(a) Disable burner by selecting ‘Heat OFF’;
‘Standby’.* (* dependent on control type
supplied. Refer to individual controller
operating manual.)
(b) The burner will turn off.
(c) The fan motor will continue to run until
heat dissipation allows the fan and limit stat
to shut down the fan.
Caution
Do not use the main electrical isolator to
turn off the heater, to do so can cause
damage to the heat exchanger and
combustion chamber and thereby invalidate
the warranty.
10.5 Shut down procedure
(a) Follow steps 10.4 (a), (b) and (c), when
main fan stops turn main electrical isolator
off, and shut oil valves
10.6 Ventilation only
(a) Enable fan on via controller by selecting
‘Fan only’; ‘Vent only’; ‘Vent/Manual’.*
(*dependent on control type supplied. Refer
to individual controller operating manual.)
(b) Fan will operate without the burner for
the set period of the controller.
10.7 Lockout situations
If either the burner or the fan and limit stat
go to lockout, the lockout must be cleared
manually before the ignition sequence can
be re-initiated.
Caution
Repeated or frequent lockouts must be
investigated and their cause determined by
a qualified and competent engineer.
10 User Instructions
Document re
feren
c
e number
20
-45-
494
March 20
14 i
s
sue
15
Replace
s
20
-45-494
M
a
y 2013
i
ssu
e 1
4
Summary of Contents for HT2000
