background image

Installation

Install filter using 2” couplers for inlet and outlet with 1” 

coupler for drain pipe. Shut-off valves should be installed 

on inlet, outlet and on drain pipe to be able to service the 

filter and isolate it when necessary. 

Pressure gauges are also recommended before and 

after the filter to easily calculate the pressure differential 

and to know when cartridge should be cleaned or 

replaced. Threaded flanged fittings for inlet and outlet 

are available by special order.

1/4” FPT Lid Fitting

One-quarter inch FPT fittings are installed 

in Waterbetter

®

 Filter lids for a number of 

customer supplied options, including 

petcock for pressure relief, pressure gauge, 

sensor, thermocouple, etc. This fitting 

should be plugged at time of installation if 

one of these options is not installed.

Part List

Hurricane

®

 Filter parts and components are listed below:

Part No.

Material

Description

550-E

EPDM

Rim gasket to seal filter

905-P

PVC

Retainer nut for filter cartridge

309SS

Stainless steel

Top plate

312

PVC

Retainer nut insert

530-AC

Stainless steel

Lid with vent

316-C

CPVC

Standpipe for HUR 40 HP

317-C

CPVC

Standpipe for HUR 90 HP

315-C

CPVC

Standpipe for HUR 170 HP

202-B

Brass

Wing-nut

329

CPVC

Inner vessel isolator

330

Stainless steel

Screw 1/4” x 1/2” for isolator

Options:

 

550-B

Buna-N

Rim gasket to seal filter

550-V

Viton

Rim gasket to seal filter

327

Stainless steel

2” Flange fittings (set of 2)

  

Available From:

Lid Fitting

P.O. Box 14066 • North Palm Beach, FL 33408
800.327.3248 • 561.848.9628 • Fax: 561.845.2474 • E-mail: [email protected]

HARMSCO

®

 Filtration Products

www.harmsco.com

003 4/07

Particle Separation

Particle separation with Hurricane

®

 filters is influenced by particle 

weight and flow rate. For optimum separation, the drain valve 

should be opened routinely by hand or automatically using a timer 

actuated valve. Automatic purge valves are not available from 

Harmsco. However, for more information regarding this equipment, 

please contact the Authorized Harmsco Distributor in your area.

The data shown below was developed through tests conducted 

with Hurricane

®

 filters and twenty micron filter cartridges to deter-

mine optimum flow rates for particle separation. Sand was used 

as the test’s particulate with a specific gravity of 2.6 relative to 

water at 1.0. This data is provided for general sizing purposes only. 

Results vary and depend on the particulate being filtered, viscosity 

and other variables.

0

25 

 

50

75

100    125     150

90
80
70
60
50
40
30
20
10

Flow Rate (GPM)

To

ta

l H

ea

d

 L

o

ss

 (

P.

S

.I.

)

100

Tests indicate the separation of performance of all three Hurricane

®

 

filters were essentially the same up to the rated flow rate of each model.

Harmsco, Inc. Industrial Filters

Limited Warranty

  1.  Harmsco, Inc. warrants its line of Industrial Filters to be free of defects in  
 

material and workmanship for a period of one year from the date of 

 

installation.

  2.  The warranty for Industrial Filters ordered with special coatings is limited 
 

only to the recoating of the defective parts due to failure in materials or  

 

workmanship for one year from date of installation.

  3.  This warranty does not cover any equipment purchased for use in 
 

applications in which the product is not suited. It is the responsibility of 

 

the buyer to determine if a product is suitable for a particular application.

  4.  THIS WARRANTY EXCLUDES THE FOLLOWING:
 

a.  Any fresh water unit installed for salt water use.

 

b.  Damage caused by improper installation, operation or care.

 

c.  Chemical attack.

 

d.  Rubber type parts and normal wear items, i.e. “o” rings, rim gaskets,  

 

   wing nuts, pipe caps, holding rods.

 

e.  Any costs of labor or expenses incurred in the removal and/or 

 

   installation of Unit, or any surrounding device.

 

f.  Damage caused by galvanic or electrolytic attack.

 

g.  Altering or removing the Harmsco, Inc. information label.

 

h. Any unit not grounded.

  5.  Service under this warranty is to be provided by the dealer/distributor who  
 

sold the unit to the distributor. If the dealer/distributor is unable to provide  

 

warranty service, contact:

Harmsco, Inc. P.O. Box 14066

North Palm Beach, Florida 33408, U.S.A.

Phone (561) 848-9628 • Fax (561) 845-2474

  A Returned Goods Authorization (RGA) number must be received from the  
  above office and placed on all shipments to and correspondence with 
  Harmsco, Inc. Please be prepared with the following information:
 

1.  Model number and serial number

 

2.  Date of installation

 

3.  Name of installer

 

4.  Nature of problem

 

5.  Your address and telephone number.

Reviews: