background image

Harman®  •  P35i-C Owner’s Manual_R3  •  2019 -___  •  03/20

7

8390-784C

NOTICE

Hearth & Home Technologies is not responsible for stove 

performance or extra maintenance required as a result of 

using fuel with higher ash or mineral content.

Storage

•  Wood pellets should be left in their original sealed bag 

until ready to use, to prevent moisture.

• 

Do not store fuel within the specified clearance areas, or 

in a location that will interfere with routine cleaning and 

maintenance procedures.

CAUTION

!

Tested  and  approved  for  use  with  wood  pellets  ONLY. 

Burning of any other fuel will void your warranty.

CAUTION

!

Do not burn fuel that contains an additive.

• 

May cause hopper fire

•  Damage to product may result

Read the list of ingredients on the packaging.

H. Fuel Specifications 

(Cont.)

BURNING COLORED PAPER, CARDBOARD, 

SOLVENTS, TRASH AND GARBAGE OR ALTERING 

THE STOVE FOR HIGHER HEAT OUTPUT MAY CAUSE 

DAMAGE TO THE STOVE AND COULD RESULT IN 

A HOUSE FIRE. USE ONLY APPROVED FUELS AND 

FOLLOW ONLY THESE OPERATION GUIDELINES.

WARNING

!

NEVER USE GASOLINE, GASOLINE-TYPE LANTERN 

FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR 

SIMILAR LIQUIDS TO START OR 'FRESHEN UP' A FIRE 

IN THIS HEATER. KEEP ALL SUCH LIQUIDS WELL 

AWAY FROM THE HEATER, WHILE IN USE.

WARNING

!

 Odors and vapors released during initial operation.

•  Curing of high temperature paint.

•  Open windows for air circulation.

Odors may be irritating to sensitive individuals.

CAUTION

!

Summary of Contents for P35i-C

























Reviews: