background image

 4

ERA 600 Performance Safety and Installation Manual

Safety Information

The following symbols are used to identify important safety information on the product and in this document:

Warning! The ERA 600 Performance from Martin® contains components that are accessible and live 
at high voltage while the fixture is connected to power. These components remain under tension for 
up to one minute after power is disconnected.

Warning! Risk Group 3 product (see “Protection from eye injury” on page 6 for full details). This 
product produces intense light output that may be hazardous if suitable precautions are not taken. 
Do not view the light output with optical instruments or any device that may concentrate the beam.

This product presents risks of severe injury or death due to fire and burn hazards, electric shock and falls if 
the safety precautions in this manual are not followed.

Read this manual

 before installing, powering or servicing the fixture. Follow the safety precautions and 

observe all warnings in this manual, in the ERA 600 Performance User Guide and printed on the fixture.

The latest versions of this Safety and Installation Manual and the ERA 600 Performance User Guide are 
available for download from the ERA 600 Performance area of the Martin website at www.martin.com. 
Before you install, operate or service the ERA 600 Performance, check the Martin website and make sure 
that you have the latest user documentation for the fixture. Document revisions are indicated at the bottom 
of page 2.

This product is for professional use only. It is not for household use. Respect all locally applicable laws, 
codes and regulations when installing, powering, operating or servicing the fixture.

Install, operate and service Martin products and accessories only as directed in their user documentation, 
or you may create a safety hazard or cause damage that is not covered by product warranties. 

The latest software, manuals and other documentation for all Martin products are available for download at 
www.martin.com

Technical Support

If you have questions about how to install or operate the fixture safely, please contact Harman Professional 
Technical support:

• For technical support in North America, please contact: [email protected]

Phone: (844) 776-4899

• For technical support outside North America, please contact your national distributor.

WARNING!

Read the safety precautions in this section before 

installing, powering, operating or servicing this 

product.

DANGER!

Safety hazard. 

Risk of severe 

injury or death.

DANGER!

Hazardous 

voltage. Risk of 
lethal or severe 

electric shock.

WARNING!

Fire hazard.

WARNING!

Burn hazard. Hot 

surface. Do not 

touch.

WARNING!

Intense light 

emission.

WARNING! Refer 

to user 

documentation.

Summary of Contents for Martin ERA 600 Performance

































Reviews: