background image

11

3-90-233R24_11/13

venting Installation

dO NOT INSTAll A FluE dAmPEr IN ThE ExhAuST 

vENTINg SYSTEm OF ThIS uNIT.

dO NOT CONNECT ThIS uNIT TO A ChImNEY FluE 

SErvINg ANOThEr APPlIANCE.

INSTAll vENT wAll PASS-ThrOughS AT ClEArANCES 

SPECIFIEd bY ThE vENT mANuFACTurEr.

INSTAllATION IS TO bE PErFOrmEd bY A QuAlIFIEd 

INSTAllEr.

NOTE: Use only 3” diameter type “L” or “PL” venting 

system. Be sure to inspect and clean exhaust venting 

system frequently.

INSTAllATION IS TO bE PErFOrmEd bY A 

QuAlIFIEd INSTAllEr.

NOTE: All installation clearances and restrictions 

must be adhered to.

To reduce probability of reverse drafting during a 

power failure, hearth & home Technologies strongly 

recommends:

•  Installing the pellet vent with a minimum vertical rise of 

five feet. Preferably terminating above the roof line.

•  Installing an outside air connection to the appliance.

To prevent soot damage to exterior walls, and to prevent 

re-entry of soot or ash into the home:

•  Maintain specified clearances to windows, doors and air 

inlets, including air conditioners.

•  Vents should not be placed below ventilated soffits.
•  Avoid venting into alcove locations.
•  Vents should not terminate under overhangs, decks or 

onto covered porches.

•  Maintain  minimum  clearance  of  12”  from  the  vent 

termination to the exterior wall.

hearth & home Technologies assumes no responsibility 

for, nor does the warranty extend to, smoke damage 

caused by reverse drafting of pellet appliances under 

power failure conditions.

NOTE: Read and follow all of the vent pipe manufacturers 

instructions on the proper installation and support of 

the vent pipe. Adhere to all clearances to combustibles.

dANgEr: rISk OF FIrE Or ExPlOSION - dO NOT 

burN gArbAgE, gASOlINE, drAIN OIl Or OThEr 

FlAmmAblE lIQuIdS IN ThIS APPlIANCE.
wArNINg: rISk OF FIrE

-   dO NOT OPErATE wITh FuEl lOAdINg Or ASh 

rEmOvAl dOOrS OPEN.

-  dO NOT STOrE FuEl Or OThEr COmbuSTIblE 

mATErIAl wIThIN mArkEd INSTAllATION 

ClEArANCES.

- INSPECT ANd ClEAN ENTIrE vENTINg 

SYSTEm INCludINg All FluES ANd ChImNEY 

rEgulArlY.

WARNING

!

kEEP COmbuSTIblE mATErIAlS SuCh AS grASS, 

lEAvES, ETC. AT lEAST 3 FEET AwAY FrOm ThE 

POINT dIrECTlY uNdEr ThE vENT TErmINATION. 

(bETwEEN ThE vENT ANd ThE grOuNd)

CAUTION

!

kEEP COmbuSTIblES AwAY 

FrOm FluE OuTlET.

Summary of Contents for HydroFlex 60 Pellet Boiler





















































Reviews: