background image

1

A -month cleaning will give you a base line 

as to how often your DVC00 needs to be cleaned. 

Cleaning intervals will differ from other DVC00 

owners because of the ash content of the coal and 

the amount of coal burned. 

NOTE:  Unit should be off & cooled down 

enough to perform these maintenance items:

1. Remove Ash Pan then remove ash shield behind 

Ash Pan, fig.22. Lift the shield up and forward in 

order to remove it from the stove. This will expose 

the Blower Cover and Latch, fig.23.

2. Rotate the Latch counterclockwise to the vertical 

position as shown in fig. 24.

3. Remove the Blower Cover by tilting the left side 

slightly forward. Next, slide the Cover left and out 

of the slot that holds the right side in place. The 

Cover can now be removed to expose the Draft 

Blower Wheel and Exhaust Outlet, fig. 25.

4. The blower wheel, blower housing, and exhaust 

outlet can now be cleaned with a brush and vac-

uum cleaner. NOTE: The ESP probe is located at 

the rear of the exhaust outlet shown in fig 28. 

Be 

careful not to damage the probe when clean-

ing.

5. Open the Fines Cover on the bottom of the feeder 

under the grates and clean, see fig.26.  

ATTEN-

TION:  MAKE  SURE  COVER  IS  CLOSED 

AND TIGHTENED BEFORE RELIGHTING 

UNIT.  UNIT WILL NOT OPERATE PROP-

ERLY WITH CLEAN OUT COVER LEAK

-

AGE.

6. Check the flue pipe for excess buildup of fly ash 

and clean if necessary.

7. Clean the glass thoroughly, use a safety razor to 

scrape the sulfur buildup from the surface of glass.  

Then clean with standard window cleaning fluid, 

fig.21.

8. Inspect all gaskets for damage and turn the control 

to "test", for motor test before relighting a fire.

Ash Shield

Tabs

Fig  22

Fig 23

Latch

Blower Cover

Fig 24

MAINTENANCE: EVERY 3 MONTHS:

Never Block Air Outlets  on top of stove, above door.

Rotate Latch

Summary of Contents for DVC-500





































Reviews: