background image

FUNCTION SWITCHES

Sidechain:

Routes external sidechain input signal to the detector.

OverEasy

®

:

Activates the OverEasy‚ compression function.

Auto:

Activates automatic program-dependent attack and release times, 
disabling the manual attack and release controls.

PeakStopPlus

®

:

Activates the Intelligent Predictive Limiting® (Stage 2) section of the limiter.

Bypass:

Activates the direct input-to-output hard-wire relay bypass.  Relay 
automatically hard-wire bypasses unit at power-down and provides a 
power-on delay of 1.5 seconds.

Input:

Monitors the input signal and shows its level on the VU meter.  Peak 
indicator lights for signals >+21dBu.

Output:

Monitors the output signal and shows its level on the VU meter.  Peak 
indicator lights for signals >+21dBu.

GR:

Monitors the compressor and PeakStopPlus limiter and displays the 
total amount of gain reduction on the lower scale of the VU meter.

Pin 1 Lift (Rear Panel)

Lifts pin 1 of the input XLR and 1/4” sleeve from chassis ground.

INDICATORS

Compressor Threshold Meter:

3 LED indicators at Below, OverEasy®, and Above.

Sidechain:

1 LED to indicate when external sidechain is selected.

Auto:

1 LED to indicate when Auto mode is selected.

PeakStopPlus

®

:

1 Bi-Color LED.  When PeakStopPlus® function is not engaged, the 
LED will be off when signal is below Stop Level threshold, and will 
light redwhen signal is above threshold.  When PeakStopPlus® 
function is engaged, the LED will be green when signal is below Stop 
Level threshold, and will turn red when signal is above threshold.

Bypass:

1 LED to indicate when 162SL is bypassed.

Input/Output/GR

3 LEDs to indicate which meter mode is selected.  Green for input 
level, yellow for output level, and red for gain reduction. 

POWER SUPPLY

Operating Voltage:

Factory selected:  100-120V, 120V, or 220-240VAC 50/60Hz.

Power Consumption:

28 Watts maximum.

Fuse:

100V-120V: T 400mA 250V; 5mm X 20mm
220V-240V: T 200mA 250V; 5mm X 20mm

Mains Connection:

IEC 320 Receptacle

PHYSICAL

Dimensions:

3.5”H X 19”W X 10”D

Weight:

11.2 lbs (5.1 kg)

Shipping Weight:

13.0 lbs (5.9 kg)

Note:   0dBu = 0.775V RMS

All Trademarks and Registered Trademarks are the property of their respective owners.

28

Summary of Contents for DBX 162SL
































Reviews: