background image

Harman®  •  Accentra52i-TC Owner’s Manual_R3  •  2017 -___  •  09/17

11

3-90-00584c

Maintenance & Service 

When properly maintained, your stove will give you many 

years of trouble-free service. 

Contact your dealer

 to answer 

questions regarding proper operation, trouble-shooting and 

service for your appliance. Visit www.harmanstoves.com to 

find a dealer. We recommend annual service by a qualified 

service technician.

Follow the detailed instructions found in this section 

for each step listed in the chart below.

Shock and Smoke Hazard

•  Turn unit to the off position, let appliance 

completely cool and combustion fan must be off. 

Now you can unplug appliance before servicing.

•  Smoke spillage into room can occur if appliance 

is not cool before unplugging.

•  Risk of shock if appliance not unplugged before 

servicing appliance.

A. Proper Shutdown Procedure

CAUTION

!

NOTICE

The type of fuel you are burning will dictate how often you 

have to clean your burnpot. 

Clean more frequently if you 

encounter  heavy  build-up  of  ash  at  the  recommended 

interval or you see soot coming from the vent.

 Not 

properly cleaning your appliance on a regular basis 

will void your warranty.

Note:

 Do not use a household vacuum to clean the stove. 

We recommend that you use a shop vacuum that is equipped 

with a fine dust filter called a HEPA filter or a vacuum specially 

made for fly ash and soot. USING A VACUUM WHICH IS 

NOT EQUIPPED WITH A FINE DUST FILTER WILL BLOW 

FLY ASH AND SOOT OUT INTO THE ROOM.

NOTE:

 THE STOVE MUST BE COMPLETELY OUT BEFORE 

YOU VACUUM THE STOVE. LIVE PELLET EMBERS, IF 

SUCKED INTO THE VACUUM, WILL LIGHT THE VACUUM 

ON FIRE AND MAY ULTIMATELY CAUSE A HOUSE FIRE.

Summary of Contents for Accentra52i-TC































Reviews: