6
Speaker Selector:
Press this button to begin
the process of configuring the unit to match the type
of speakers used in your listening room. (See pages
26–28 for more information on speaker setup and
configuration.)
7
Surround Mode Group Selector:
Press this but-
ton to select the top-level group of surround modes.
Each press of the button will select the current or last
used mode in each of the surround mode groups
(e.g., Dolby, DTS, DTS Neo:6, Logic 7, DSP, Stereo).
When the button is pressed so that the name of the
surround mode group appears in the on-screen dis-
play and in the
Lower Display Line
ı
, press the
Surround Mode Selector
8
to cycle through the
individual modes available. For example, press this
button to select Dolby modes, and then press the
Surround Mode Selector
8
to choose from the
various Dolby mode options.
8
Surround Mode Selector:
Press this button
to select from among the available surround mode
options for the mode group selected. The specific
modes will vary based on the number of speakers
available, the mode group and if the input source is
digital or analog. For example, press the
Surround
Mode Group Selector
7
to select a main mode
grouping such as Dolby or Logic 7, and then press
this button to see the specific mode choices available.
Note that the digital surround modes, such as Dolby
Digital and DTS, may not be accessed unless that type
of source signal is present, such as when a DVD movie
or television signal programmed in Dolby Digital or DTS
surround sound is playing. For more information on sur-
round mode selection, see pages 23 and 32.
9
Tuning Selector:
Press the left side of the button
to tune lower-frequency stations and the right side of
the button to tune higher-frequency stations. When the
tuner is in the Manual mode, each tap will increase or
decrease the frequency by one increment. When the
tuner receives a strong enough signal for adequate
reception,
MANUAL TUNED
will appear in the
on-screen display and the
Lower Display Line
ı
.
When the tuner is the Auto mode, press the button
once, and the tuner will scan for a station with accept-
able signal strength. When the next station with a
strong signal is tuned the scan will stop and the
on-screen display and
Lower Display Line
ı
will indicate
AUTO TUNED
. When an FM
Stereo station is tuned, the display will read
A
UTO ST TUNED
.
To switch back and forth between the Auto and
Manual tuning modes, press the
Tuner Mode
Selector
&
.
)
‹
/
›
Buttons:
When configuring the AVR 240’s
settings, use these buttons to select from the available
choices.
!
Tuner Band Selector:
Press this button to turn
the AVR on and to select the Tuner as the input. Press
it again to switch between the AM and FM frequency
bands. (See page 37 for more information on the tuner.)
@
Set Button:
When making choices during the
setup and configuration process, press this button
to enter the desired setting into the AVR 240’s memory.
#
Digital Input Selector:
Press this button to
select one of the digital audio inputs or the analog
audio input for any source. (See pages 32–37 for
more information on digital audio.)
$
Preset Stations Selector:
Press this button to
scroll up or down through the list of stations that have
been entered into the preset memory. (See page 37
for more information on tuner presets.)
%
Delay Adjust Selector:
Press this button to
begin the steps required to enter delay settings. (See
pages 28–29 for more information on delay times.)
^
Input Source Selector:
Press this button to
change the input by scrolling up or down through the
list of
Input Indicators
Ú
.
&
Tuner Mode Selector:
Press this button to select
Auto or Manual tuning. When the button is pressed so
that the
AUTO
appears in the
Lower Display Line
ı
, the tuner will search for the next station with an
acceptable signal when the
Tuning Selector
9u
is pressed. When the button is pressed so that
MANUAL
appears in the
Lower Display Line
ı
,
each press of the
Tuning Selector
9u
will
increase the frequency. This button may also be used to
switch between Stereo and Mono modes for FM radio
reception. When weak reception is encountered, press
the button so that
MANUAL
appears in the
Lower
Display Line
ı
and on the on-screen display to
switch to Mono reception. Press it again to switch back
to Stereo mode. (See page 37 for more information on
using the tuner.)
*
Optical 3 Digital Audio Input:
Connect the optical
digital audio output of an audio or video product to this
jack. When the input is not in use, the built-in shutter will
close to avoid dust contamination that might degrade
future performance.
(
Coaxial 3 Digital Audio Input:
This jack is used
for connection to the output of portable audio devices,
video game consoles or other products that have a
coax digital audio jack.
Ó
Video 4 Video Input Jacks:
These jacks may
be used for temporary connection to the composite or
S-video output of video games, camcorders or other
portable video products. You may make a connection
to either jack at any time, but not to both simultaneously.
Ô
Video 4 Audio Input Jacks:
These audio jacks
may be used for temporary connection to video
games or portable audio/video products such as
camcorders and portable audio players.
Channel Adjust Selector:
Press this button to
begin the process of trimming the channel output lev-
els using an external audio source. (For more informa-
tion on output level trim adjustment, see page 38.)
Ò
Volume Control:
Turn this knob clockwise to
increase the volume, counterclockwise to decrease
the volume. If the AVR 240 is muted, adjusting the
Volume Control
Ò
b
will automatically release
the unit from the silenced condition.
Ú
Input Indicators:
The current selected source
will appear as one of these indicators. When the unit
is turned on, the entire list of available modes will
light briefly, and then revert to normal operation with
only the active mode indicator illuminated.
NOTE
: When
/DMP has been selected as
the input source, no
Input Indicator
N
will light.
DMP/THE BRIDGE IS CONNECTED
will scroll across the
Upper Display Line
P
, unless
you have retitled the source name, in which case that
name will appear. See page 20 for more information
on input titling.
Û
Speaker/Channel Input Indicators:
These indi-
cators are multipurpose, indicating both the speaker
type selected for each channel and the incoming data-
signal configuration. The left, center, right, right surround
and left surround speaker indicators are composed of
three boxes, while the subwoofer is a single box. The
center box lights when a “small” speaker is selected,
and the two outer boxes light when “large” speakers are
selected. When none of the boxes are lit for the center,
surround or subwoofer channels, no speaker has been
assigned that position. (See pages 26–28 for more
information on configuring speakers.)
The letters inside each box display the active input
channels. For standard analog sources, only the L and R
will light, indicating a stereo input. For a digital source,
the indicators will light to display the channels being
received at the digital input. When the letters flash, the
digital input has been interrupted. (See page 36 for
more information on the Channel Indicators.)
Ù
Upper Display Line:
Depending on the unit’s sta-
tus, a variety of messages will appear here. In normal
The
Bridge
TM
FRONT-PANEL CONTROLS
6 FRONT-PANEL CONTROLS
FRONT-PANEL CONTROLS
