Harman Kardon AVR 240 Owner'S Manual Download Page 20

Page: 20 / 60

SYSTEM CONFIGURATION

In addition to the previously mentioned settings, which
always vary with the input, you may also choose to set
different speaker size configurations for each input. In
most cases, this is not required, thus the factory
default keeps these settings the same for all inputs.
However, should you wish to have these settings
change for any one, or all, inputs, follow the instruc-
tions shown on page 27 to select the Independent
mode for speaker configuration.

The first time you use the AVR 240, we recommend
that you take advantage of the simplicity of configuring
the system using the EzSet+ process, which takes the
guesswork out of speaker size and delay settings, and
balances the speaker output levels to tailor the AVR’s
sound presentation to your specific system and room.
Before beginning the EzSet+ procedure, there are a
few adjustments that need to be made to ensure
accurate results.

The factory default settings for the AVR 240 have all
inputs configured for an analog audio input except
for the DVD input, where the

Coaxial Digital Audio

Input 1

is the default, and the Video 2 input,

where the

Optical Digital Audio Input 1

is the

default. The default speaker settings are for “Small”
at all positions, and the subwoofer on.

The default surround mode setting for all sources
using an analog input is the Logic 7 Music mode.
Dolby Digital or DTS will always be automatically
selected anytime a source with digital encoding in that
format is in use. When a Dolby Digital 2.0 source is
detected, the AVR 240 will automatically add Dolby
Pro Logic II or IIx processing. Once a surround mode
is selected for a particular source, the AVR 240 will
default to that surround mode the next time the source
is selected, unless the input signal is in a Dolby Digital
or DTS digital format. For Dolby Digital and DTS mate-
rials, the AVR 240 will default to the surround mode
encoded in the bitstream. As explained on pages
35–36, you may select from a limited number of
other surround modes for these materials. If you wish
to have the AVR 240 default to one of these alternate
surround modes each time a Dolby Digital or DTS
source is encountered, you may use the Default
Surround Mode setting in the

ADVANCED

SELECT

submenu (see page 39).

Before using the unit, you will probably want to pro-
gram the settings for most inputs so that they are
properly configured to reflect the use of digital or ana-
log audio inputs, component video inputs and the sur-
round mode specifics of your home theater system.
Remember that since the AVR 240 memorizes these
settings for each input independently, you will need to
make some of these adjustments for each input used.
However, once they are made, further adjustment is
only required when system components are changed.

To make this process as quick and easy as possible,
we suggest that you use the full-OSD system with the
on-screen menus, and step through each input. It is
also a good idea to set the configuration data in the
order these items are listed in the

MASTER

MENU

, as some settings require a specific entry

in a prior menu item. It is recommended that you
record your settings for each input using the work-
sheets in the appendix to this manual, in the event
there is a power loss or if you need to reenter the
settings for some other reason.

Input Setup

The first step in configuring the AVR 240 is to configure
each input. Once an input is configured, all settings for
the Digital Input, Component Video Input and Surround
Mode will “attach” themselves to that input and be
stored in a nonvolatile memory. The later selection of
that input will automatically recall those settings. For
that reason, the procedures described below must be
repeated for each input source so that you have the
opportunity to customize each source to your specific
listening requirements. However, once made, they
need not be changed again unless you need to alter
a setting.

When using the full-OSD system to make the setup
adjustments, press the

OSD Button

once so that

the

MASTER MENU

(Figure 1) appears. The

›

cursor will be next to the

INPUT SETUP

line.

Press the

Set Button

to enter the menu and the

INPUT SETUP

menu (Figure 2) will appear on

the screen. Press the

‹

›

Buttons

until the

desired input name appears in the highlighted video,
as well as being indicated in the front-panel

Input

Indicators

. If the input will use the standard left/

right analog inputs and will not use component video,
no further adjustment is needed.

NOTE

: The

DIGITAL IN

line will default to

COAXIAL 1

when the DVD input is selected.

Similarly, when the Video 2 input is selected,
the

DIGITAL IN

line will default to

OPTICAL 1

Figure 2

The AVR 240 offers you the opportunity to rename
any source (except the tuner) to customize it for your
particular equipment configuration, e.g. to designate

the source input to which you have connected a VCR,
or a DVD-Audio player. This name will appear in the

Upper Display Line

and in the on-screen display

whenever that source input is selected. If you wish to
rename a source, press the

Button

until the

›

cursor is pointing to the

NAME:

line. Press the

Set Button

. A flashing box will appear. Press the

⁄

Button

to scroll through the letters of the

alphabet first in upper case, then in lower case, then
the numerals 0 through 9, and then followed by the
symbols ! ‘ ( ) * + , - . / ; < = > ? [ ] and then a
blank space. Use the

Button

to scroll in the

reverse order. Use the

‹

›

Buttons

to move

from one character to the previous or following char-
acter. You may create a name of up to 14 characters,
including spaces. Press the

Set Button

when

you have finished entering the name, and then press
the

Button

to proceed to the next setting.

If your system includes any sources that are equipped
with Y/Pr/Pb component video outputs, the AVR 240
is able to switch them to send the proper signals to
your video display. Each of the two

Component

Video Inputs

›fi

may be assigned to a source for

added system flexibility. The

Component Video 1

Input

›

may be assigned to any one of the DVD,

Tuner, CD or Tape inputs. The

Component Video 2

Input

may be assigned to any one of the Video 1

(VCR), Video 2 (Cable/Sat), Video 3 (TV) or 6/8-
Channel Direct inputs. If your system does not include
component video at this time, or if you do not need to
change these defaults, press the

Button

go to the next setting.

To change the Component Video assignment, first
make certain that the cursor is pointing to the

COMPONENT IN

line on the menu screen, and

then press the

‹

›

Buttons

until you see the

desired input. When the desired component video
input has been selected, press the

Button