background image

ENGLISH

TECHNICAL SPECIFICATIONS

35

Technical Specifications

Audio Section

Stereo Mode 
Continuous Average Power (FTC)

40 Watts per channel, 20Hz–20kHz,
@ < 0.07% THD, both channels driven into 8 ohms

Five-Channel Surround Modes 
Power Per Individual Channel

Front L&R channels:
30 Watts per channel,
@ < 0.07% THD, 20Hz–20kHz into 8 ohms

Center channel:
30 Watts, @ < 0.07% THD, 20Hz–20kHz into 8 ohms

Surround channels:
30 Watts per channel,
@ < 0.07% THD, 20Hz–20kHz into 8 ohms

Input Sensitivity/Impedance 

Linear (High Level)

200mV/47kohms

Signal-to-Noise Ratio (IHF-A)

95dB

Surround System Adjacent Channel Separation 

Analog Decoding 

40dB 

(Pro Logic, etc.) 
Dolby Digital (AC-3) 

55dB 

DTS

55dB

Frequency Response 

@ 1W (+0dB, –3dB)

10Hz–100kHz

High Instantaneous 
Current Capability (HCC)

±25 Amps

Transient Intermodulation 
Distortion (TIM)

Unmeasurable

Rise Time

16 µsec

Slew Rate

40V/µsec

FM Tuner Section

Frequency Range

87.5–108MHz

Usable Sensitivity

IHF 1.3 µV/13.2dBf

Signal-to-Noise Ratio

Mono/Stereo: 70/65dB (DIN)

Distortion

Mono/Stereo: 0.15/0.3%

Stereo Separation

35dB @ 1kHz

Selectivity

±400kHz: 70dB

Image Rejection

80dB

IF Rejection

90dB

AM Tuner Section

Frequency Range

522–1620kHz

Signal-to-Noise Ratio

45dB

Usable Sensitivity

Loop: 500µV

Distortion

1kHz, 50% Mod: 0.8%

Selectivity

±10kHz: 30dB

Video Section

Video Format

PAL/NTSC

Input Level/Impedance

1Vp-p/75 ohms

Output Level/Impedance 1Vp-p/75 ohms
Video Frequency 
Response

10Hz–8MHz (–3dB)

General

Power Requirement

AC 220-240V/50Hz

Power Consumption

72W idle, 580W maximum 
(2 channels driven)

Dimensions (Max)

Width

440mm 

Height

165mm 

Depth

382mm

Weight

9.6 kg

Depth measurement includes knobs, buttons and terminal connections.
Height measurement includes feet and chassis.
All features and specifications are subject to change without notice.

Harman Kardon is a registered trademark.

*Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the Double-D symbol are 
trademarks of Dolby Laboratories, Inc.
Confidential Unpublished Works. ©1992–1999 Dolby Laboratories, Inc.
All rights reserved.

†"DTS" and "DTS Neo:6" are registered trademarks of DTS, Inc. "96/24" 
is a trademark of DTS, Inc.

Logic 7 is a registered trademark of Lexicon, Inc.

29782_AVR132_ENG  29/11/06  12:07  Side 35

Summary of Contents for AVR 132





































Reviews: