Big Boat High-Load End Controls and Trim Caps
End Controls: 3173, 3174 • Track: 3154, 3155, 3159, 3162, 1846, R32, 3156, R32HB
Trim Caps: 3157, 3158
Read instructions Before You Cut, Drill or Mount Track
To cut track to length, make sure stop holes for control blocks do not interfere
with hole for mounting track. If necessary, cut both ends of track.
It may be necessary to put trim caps, control blocks and traveler car on track
before mounting. Slide control assemblies onto track with bumper facing car.
Keep control assembly loose so it can be moved away while installing track.
Track Cutting Considerations
Dead-ending Line at End Control
Remove any burrs on edges of track. Press 3157 or 3158 trim caps in place.
Important: insert trim caps before drilling outboard control block hole.
To determine correct track length, make sure track ends, without trim caps, are
13
/
16
" (21 mm) from edge of cockpit coaming to allow room for trim caps.
Install Trim Caps in Track Ends
Cockpit Installation—Allow Room for Trim Caps
Cut both ends of track to prevent interference with existing holes in track
No
Yes
Drill
27
/
64
" (10.5 mm) hole
through top surface of track
only.
Important: Do not use screw hole in control block as a drill guide.
Position Control Block/Drill Track/Secure Control
Position control block flush with end of track. Drive screw firmly against top
surface to mark track, then loosen. Slide control block away.
13
/
16
"
(21 mm)
4
9
/
16
" (116 mm)
7
/
16
"
(11 mm)
Secure control block to track by tightening correct screw into hole.
Cockpit
Edge
I N S T R U C T I O N S
USA
–
Tel:
(+1) 262-691-3320 •
Web:
www.harken.com •
Email:
Italy
–
Tel:
(+39) 031.3523511 •
Web:
www.harken.it •
Email:
IMPORTANT: See Inspection and Maintenance at end of manual.
Note:
3173, 3174 end controls do not fit older non-CB track. The interior ridges that
extend into the waist of the track are too deep to fit non-CB track. 3173 and 3174
controls require track with deep grooves for the wire keepers used on CB cars.
Strictly follow all instructions to avoid an accident, damage to
your vessel, personal injury or death. See www.harken.com/
manuals for additional safety information.
3156, R32HB
Use 45 mm Screws
3154, 3155, 3159, 3162, 1846, R32
Use 25 mm Screws
Big Boat High-Load End Controls and Trim Caps
End Controls: 3173, 3174 • Track: 3154, 3155, 3159, 3162, 1846, R32, 3156, R32HB
Trim Caps: 3157, 3158
Read instructions Before You Cut, Drill or Mount Track
To cut track to length, make sure stop holes for control blocks do not interfere
with hole for mounting track. If necessary, cut both ends of track.
It may be necessary to put trim caps, control blocks and traveler car on track
before mounting. Slide control assemblies onto track with bumper facing car.
Keep control assembly loose so it can be moved away while installing track.
Track Cutting Considerations
Dead-ending Line at End Control
Remove any burrs on edges of track. Press 3157 or 3158 trim caps in place.
Important: insert trim caps before drilling outboard control block hole.
To determine correct track length, make sure track ends, without trim caps, are
13
/
16
" (21 mm) from edge of cockpit coaming to allow room for trim caps.
Install Trim Caps in Track Ends
Cockpit Installation—Allow Room for Trim Caps
Cut both ends of track to prevent interference with existing holes in track
No
Yes
Drill
27
/
64
" (10.5 mm) hole
through top surface of track
only.
Important: Do not use screw hole in control block as a drill guide.
Position Control Block/Drill Track/Secure Control
Position control block flush with end of track. Drive screw firmly against top
surface to mark track, then loosen. Slide control block away.
13
/
16
"
(21 mm)
4
9
/
16
" (116 mm)
7
/
16
"
(11 mm)
Secure control block to track by tightening correct screw into hole.
Cockpit
Edge
I N S T R U C T I O N S
USA
–
Tel:
(+1) 262-691-3320 •
Web:
www.harken.com •
Email:
Italy
–
Tel:
(+39) 031.3523511 •
Web:
www.harken.it •
Email:
IMPORTANT: See Inspection and Maintenance at end of manual.
Note:
3173, 3174 end controls do not fit older non-CB track. The interior ridges that
extend into the waist of the track are too deep to fit non-CB track. 3173 and 3174
controls require track with deep grooves for the wire keepers used on CB cars.
Strictly follow all instructions to avoid an accident, damage to
your vessel, personal injury or death. See www.harken.com/
manuals for additional safety information.
3156, R32HB
Use 45 mm Screws
3154, 3155, 3159, 3162, 1846, R32
Use 25 mm Screws
