background image

06/29/09 

External Access System 

5

It is the responsibility of the user and the purchaser of this equipment to assure that they are familiar with these 

instructions, trained in the correct care and use of, and are aware of the operating characteristics, application 

limits, and the consequences of improper use of this equipment.

PERSONAL FALL ARREST EqUIPMENT 

When using a hook with positive locking mechanism to connect to car shackle, ensure roll-out cannot occur. 

Roll-out occurs when interference between hook and mating connector causes hook gate to unintentionally open 

and release.
Self-locking snap hooks and carabiners should be used to reduce possibility of roll-out. Do not use hooks or 

connectors that will not completely close over attachment object. 
Follow manufacturer’s manual for correct use of energy-absorbing lanyard. 
Follow manufacturer’s instruction manual for correct use of bosun’s chair and certified safety harness.
Do not attach a connector such that it will impact on the side of the car when in use.

WARNING: This product is part of a personal fall arrest system. 

The user must follow the manufacturer’s  

instructions for each component of the system. These instructions must be provided to the user of this  

equipment. The user must read and understand these instructions before using this equipment. Manufacturer’s 

instructions must be followed for proper use and maintenance of this equipment. Alterations or misuse of this 

equipment, or failure to follow these instructions, may result in a fall or failure to arrest a fall leading to serious 

injury or death.

4) Use

5) Training

6) Inspection

INSPECT BEFORE EACH USE

C

B

E

B

B

B

A

C

D

A formal inspection of the track and its connection to the structure must be  

performed at least annually by a competent person other than the user. 
The inspection should be recorded in an inspection and maintenance log.

BEFoRE EACH uSE

A) Inspect pinstop for spring degradation, cracks or wear that may affect locking 

strength and operation.  Check drive pin holding plastic latch to post to make sure  

it is secure.

WARNING: 

If pinstop locking mechanism fails cars may become loose  

on track resulting in an uncontrolled slide along track resulting severe  

injury and death.

A

Drive Pin

Summary of Contents for H-50547





















Reviews: