background image

The manufacturer further disclaims any claims for damages resulting from improper use, 

negligence, modifications, attempted repairs by unauthorized persons, or acts of God.

The repair or replacement of defective parts does not lead to an extension or restart of 

the warranty period according to the warranty conditions.

ATTENTION!

If any problems occur during operation of your product, please contact 

your local distributor or authorized representative immediately and clarify 

to what extent this malfunction is covered by the warranty and/or 

guarantee. Under no circumstances should you make any changes or 

repairs to your product yourself!

The company 

eCharge Hardy Barth GmbH

 assures the proper operation of the present 

product after delivery within the scope of the legally valid warranty. 

The warranty is limited to such damage that is due to normal use and obvious material 

or manufacturing defects. 

In these cases, the manufacturer, in cooperation with the local distributor, will attempt to 

restore the proper function of the product. 

Any costs incurred for the transport of the product shall be borne by the customer.

If the serial number has been removed from the Wallbox, altered or made illegible 

through the fault of the customer, all rights granted under the warranty conditions shall 

expire and only the statutory warranty period shall apply.

If the customer orders an execution of repair or replacement work outside the business 

hours of 

eCharge Hardy Barth GmbH

, the hourly wage and the travel expenses outside 

the normal business hours (Monday - Friday 9:00 - 16:00) will be charged to the 

customer according to the current price list.

Customer service for questions, complaints and claims:

Monday to Thursday from 8:00 - 12:00 and 13:00 - 17:00.

Friday from 8:00 - 16:00 under the telephone 49 9666 / 188 00 50,

as well by e-mail at 

[email protected]

Please have the serial number, the product designation of the Wallbox and your 

customer number ready!

Installation and operating manual 

cPH2

 charging station

Version: 1.0.9

28

Summary of Contents for cPH2 1T11





























Reviews: