Hardinge Talent 10/78 Maintenance Manual Download

Page: 57 / 104

5. Set the Mode Select switch to Reference mode.

6. Set the Turret Station selector switch "12".

7. Press and hold the Turret Index push button for 2 seconds. The turret will not index.

8. Set K00, bit 6 to "0". The alarm message will be cleared from the display.

9. Press the Turret Index push button. The turret will index to station 12.

10. Test the turret by setting the Turret Station selector switch to other turret stations and pressing

the Turret Index push button.

11. Set the Mode Select switch to Manual Data Input mode.

12. Set Parameter Write Enable (PWE) to "0".

A) Press the Offset Setting key. The Setting page that contains the Parameter Write field will be

displayed.

B) Press the Operator soft key

C) Press the OFF:0 soft key.

13. Press the control Reset key.

M-448B

6-7

Summary of Contents for Talent 10/78









































































































Search results

Summary of Contents for Talent 10/78

Reviews:

Related manuals for Talent 10/78

Brands by name

Popular brands

Hardinge Talent 10/78, Maintenance Manual

Search results

Summary of Contents for Talent 10/78

Reviews:

Related manuals for Talent 10/78

Brands by name

Popular brands