Hardinge Talent 10/78 Maintenance Manual Download

Page: 20 / 104

LUBRICATION ALARM

The control issues the following lubrication alarms:

•

Axis lubrication alarm message after 600 hours of operation.

•

Turret lubrication alarm message after 2000 hours of operation. (Live tooling machines
only)

A lubrication alarm does not stop the machine, but will inhibit Cycle Start.

Clear the alarm message as follows:

If the machine is equipped with a Fanuc control, press the Feed Hold and Reset push but-
tons at the same time to clear the alarm.

If the machine is equipped with a Siemens control, press the Reset key AND HOLD FOR 5
SECONDS to clear the alarm.

GREASE VOLUME

The grease volume presented is dependent upon the grease gun being used. Carefully measure

the amount of grease or count the grease gun strokes necessary to lubricate the guides and ball
screws. Be certain that all air is purged from any grease gun before use.

- NOTE -

The grease gun supplied with the machine delivers 3 cc per full stroke.

The required amount of grease is:

Linear Guides:

3½ cc

Ball Screws:

11 cc

Make certain that all the sliding surfaces are lubricated well by jogging the axes at 50% of the

maximum rapid traverse for a full 30 minutes before resuming automatic operation.

2-2

M-448B

Summary of Contents for Talent 10/78









































































































Search results

Summary of Contents for Talent 10/78

Reviews:

Related manuals for Talent 10/78

Brands by name

Popular brands

Hardinge Talent 10/78, Maintenance Manual

Search results

Summary of Contents for Talent 10/78

Reviews:

Related manuals for Talent 10/78

Brands by name

Popular brands