manualshive.com logo in svg

Hardi Mercury Series, Instruction Book

Share
Download
Hardi Mercury Series Instruction Book Download Page 4

4

Liquid system  ......................................................................................................................................35

General information  .......................................................................................................................................................................................... 35
The liquid circuit  .................................................................................................................................................................................................. 35
Diaphragm pump ............................................................................................................................................................................................... 35
Valves .......................................................................................................................................................................................................................... 35
Valves and symbols ............................................................................................................................................................................................ 35
Manifold system (Zaturn only) .................................................................................................................................................................... 36
Agitation / Tank rinse valve (Zaturn only) ............................................................................................................................................ 36
Pressure valve (Zaturn only)  ......................................................................................................................................................................... 36
Suction valve (Zaturn only) ........................................................................................................................................................................... 36
Agitator (Zaturn) .................................................................................................................................................................................................. 37
Agitator (Mercury)  .............................................................................................................................................................................................. 37

Rate Controller DB3610 .......................................................................................................................38
Axial blower units ................................................................................................................................39

Technical information  ...................................................................................................................................................................................... 39
AG820 and SF65 ................................................................................................................................................................................................... 39
Air flow of axial blower Zaturn .................................................................................................................................................................... 40
Deflectors ................................................................................................................................................................................................................. 41
Specific for SF fans .............................................................................................................................................................................................. 42
Powder mixer  ........................................................................................................................................................................................................ 43

Centrifugal Blower Units (Turbines)  ....................................................................................................44

General information  .......................................................................................................................................................................................... 44
Air flow of HF640D centrifugal turbines  ............................................................................................................................................... 45
Protective grid ....................................................................................................................................................................................................... 45
 Gearbox .................................................................................................................................................................................................................... 46
HF 640D Turbines  ............................................................................................................................................................................................... 46
Clutch (All blower types)  ................................................................................................................................................................................ 46

Equipment ...........................................................................................................................................47

Ring drawbar .......................................................................................................................................................................................................... 47
Turnable drawbar ................................................................................................................................................................................................ 47
Wedges ..................................................................................................................................................................................................................... 47

Boom ...................................................................................................................................................48

Breakaway Arms ................................................................................................................................................................................................... 48

4 - Sprayer setup

Connecting the articulated drawbar  ...................................................................................................................................................... 50
Lock device on turnable drawbar ............................................................................................................................................................. 51

Hydraulic connections  .........................................................................................................................53

General information  .......................................................................................................................................................................................... 53

Electrical connections ..........................................................................................................................54

General information  .......................................................................................................................................................................................... 54
Operating unit  ...................................................................................................................................................................................................... 54

Rate controller  .....................................................................................................................................55

Rate controller DB 3610  .................................................................................................................................................................................. 55

Fluid circuit  ..........................................................................................................................................56

Deflectors ................................................................................................................................................................................................................. 57
V deflector  ............................................................................................................................................................................................................... 57
Top S or L  ................................................................................................................................................................................................................. 57
Adjustable bottom deflector  ....................................................................................................................................................................... 58
DUO T and V deflector ..................................................................................................................................................................................... 59

Boom Adjustments  ..............................................................................................................................60

Boom Width - Row Spacing  ......................................................................................................................................................................... 60
Crop Height Adjust  ............................................................................................................................................................................................ 60
Adjustable Boom Tube Length & nozzle positioning  .................................................................................................................. 61

Electrical connections ..........................................................................................................................62

Installation of control unit brackets ......................................................................................................................................................... 62
Road safety kit  ....................................................................................................................................................................................................... 62
Power supply  ......................................................................................................................................................................................................... 63

Summary of Contents for Mercury Series



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands