Hardi Mercury Series Instruction Book Download Page 13

Page: 13 / 114

2 - General Safety Instructions

Risk of squeezing!

Stay clear of raised and unsecured loads.

Risk of squeezing

Never reach into the crushing danger area as
long as parts are moving.

Risk of squeezing!

Keep hands away, when parts is moving.

Risk of falling off!

Do not ride on platform or ladder.

Risk of sprayer tipping over!

Be aware when disconnecting the sprayer.

Grapping area!

Manual handling of the boom etc.

Not for drinking!

This water must never be used for drinking.

Not for drinking!

This water must never be used for drinking.

Lifting point!

Load index!

Max. permitted load rating is 164 at 40 km/h
or 5000 kg.

EasyClean filter service!

Open and clean filter monthly.

Summary of Contents for Mercury Series



















































































































Search results

Summary of Contents for Mercury Series

Reviews:

Related manuals for Mercury Series

Brands by name

Popular brands

Hardi Mercury Series, Instruction Book

Search results

Summary of Contents for Mercury Series

Reviews:

Related manuals for Mercury Series

Brands by name

Popular brands