background image

Page 3

For technical questions, please call 1-888-866-5797.

ITEM 59134 

        

SAFETY

SETU

p

Op

ERA

TION

M

AINTENANCE

10. Use only lubricants and fuel 

recommended in this manual.

11.  Improper connections to a building electrical system 

can allow electrical current from the Generator 

to backfeed into the utility lines.  Such backfeed 

may electrocute utility company workers or others 

who contact the lines during a power outage, and 

the Generator may explode, burn, or cause fires 

when utility power is restored.  Consult the utility 

company and a qualified electrician if intending 

to use the Generator for back up power.

12. Do not operate the Generator before grounding.  

The Generator must be earth-grounded 

in accordance with all relevant electrical 

codes and standards before operation.

13. Install carbon monoxide alarm(s) with 

battery backup in nearby buildings according 

to manufacturer’s instructions.

Operating precautions

1. 

 

 

CARBON MONOXIDE HAZARD  

 

 

USING A GENERATOR INDOORS  

 

 

CAN KILL YOU IN MINUTES. 

  

Generator exhaust contains carbon 

monoxide.  This is a poison you cannot see or smell.

 

NEVER use inside a home or garage, EVEN IF 

doors and windows are open.

 

Only use OUTSIDE and far away from 

windows, doors, and vents.

2. 

CARBON MONOXIDE SHUTOFF

DANGER! TO pREVENT SERIOUS 

INJURY AND DEATH FROM 

CARBON MONOXIDE INHALATION: 

The Carbon Monoxide sensor is an additional 

layer of protection only.  Do not use the 

Generator in any area or situation that will 

allow carbon monoxide to accumulate.

•  FLASHING RED LIGHT: 

Dangerous levels of carbon monoxide gas have 

built up and generator will shutoff.   

Leave immediately until area has aired 

out. Move Generator to well-ventilated 

area before operation.

•  FLASHING YELLOW LIGHT: 

Carbon monoxide sensor malfunction. 

Sensor needs service.  Do not use the 

Generator until the sensor is working 

properly.  For technical questions, 

please call 1-888-866-5797.

NOTE: Yellow light flashes once after 

starting to indicate passing self-check 

and is functioning normally. 

Carbon Monoxide sensor must only be serviced 

by qualified technician to restore it to original 

settings.  Do not modify or tamper with the 

Carbon Monoxide sensor. Not following these 

instructions can result in death or serious injury 

due to Carbon Monoxide sensor malfunction.

3.  Never use a generator indoors, including in 

garages, basements, crawlspaces and sheds.  

Opening doors and windows or using fans will NOT 

prevent carbon monoxide build up in the home.

4.  When using generators, keep them outdoors 

and far away from open doors, windows, 

and vents to avoid toxic levels of carbon 

monoxide from building up indoors.

5.  If you start to feel sick, dizzy, or weak while 

using a generator, get to fresh air right away.  

The carbon monoxide from generators can 

quickly lead to full incapacitation and death.

6.  Keep children away from the equipment, 

especially while it is operating. 

7.  Keep all spectators at least six feet 

from the Engine during operation.

8.  Do not touch engine during use.  

Let engine cool down after use. 

9.  Never store fuel or other flammable 

materials near the engine.

Set up precautions (continued)

Summary of Contents for PREDATOR 59134

































Reviews: