background image

Page 4

For technical questions, please call 1-888-866-5797.

Item 56617 

        

Sa

FE

ty

Op
Era

tIO

n

Ma
Int

Enanc

E

SE

tup

Operating Instructions

  read the EntIrE IMpOrtant SaFEty InFOrMatIOn section at the beginning of this 

manual including all text under subheadings therein before set up or use of this product.

tool Set up

attaching the Handle

cautIOn! the Handle socket may be held 

down by a clip under tension.  Wear anSI-

approved safety goggles before freeing 

Handle socket.  remove clip carefully. 

1.  Align the hole on the Lower Handle with 

the Handle Lock Button and connect 

the Upper and Lower Handles together.  

Make sure the Button clicks into place.

2.  Loosen the Set Screw and insert the 

assembled Handle into the Handle Socket.

3.  Tighten the Set Screw.

Bleeding

1.  Turn handle counterclockwise 

to open Release Valve. 

2.  Remove four screws holding on pump cover.

3.  Remove Oil Fill Plug and top off hydraulic oil.

4.  Apply pressure to saddle and quickly 

pump handle several times.

5.  Check Oil Fill Hole again and top off 

with hydraulic oil if necessary.

6.  Replace the Oil Fill Plug and turn handle 

clockwise to close Release Valve.

7.  Test several times for proper operation 

before attempting to lift a load.

adding Oil

1.  Remove the Fill Screw. 
2.  Add high grade hydraulic fluid into the Fill Screw 

slowly until the oil reaches the top of the oil fill hole.

Note: Do not touch the Handle when 

adding the hydraulic oil. 
3.  Replace the Fill Screw.

Summary of Contents for PITTSBURGH 56617









Reviews: