Harbor Freight Tools 93661 Set Up And Operating Instructions Manual Download Page 3

Page 3

For technical questions, please call 1-800-444-3353.

SKU 93661 

        

reV 09j, 10d

or property damage.  Contact your local 

hazardous waste disposal authority for 

proper disposal.
The warnings, cautions, and instructions 

14. 

discussed in this instruction manual 

cannot cover all possible conditions and 

situations that may occur. It must be 

understood by the operator that common 

sense and caution are factors which 

cannot be built into this product, but must 

be supplied by the operator.

 SpeciFicationS

Lamp

6 V, 10 W Quartz lamp  

(equivalent to 60 W)

Battery Pack

6 V, 1300 mAh, (5x‘AA’ NiCd)

Solar Panel

7” X 7-1/2” polycrystalline silicon

Detects Motion

6’ 5” up to 60’

Range of Motion Up to 180°

Delay Time

5 to 120 seconds; adjustable

unpacKing

When unpacking the Solar Powered 

Security Light, check to make sure parts on 

page 8 are included.  If any parts are missing 

or broken, please call 

harBor Freight 

toolS 

at 

1-800-444-3353.

coMponentS

Figure 1

Power 

Switch 

(7)

FRONT

BACK

Solar Panel (2)

Lamp (1)

Mounting 

Bracket 

(13)

Hinged Mounting 

Bracket (8)

Power Cord

Motion Detector Head (6)

Outlet 

for 

Power 

Cord

Summary of Contents for 93661













Reviews: