background image

TROUBLESHOOTING

16

Lowes.com/harborbreeze

 

Fan Wobbles.

8. Fan too close to vaulted 

ceiling.

8. Lower or move fan. Extension downrods 

may be ordered.

9. Transition to different speed. 9. When switching from medium to low speed, 

you may notice some fan wobble in the fan. 

When the fan stabilizes at low speed, wobble 

should disappear.

10. Fan not securely mounted. 10. Make sure canopy and mounting bracket 

are tightened securely to ceiling joist.

1. Power turned off, fuse blown 

or circuit breaker tripped.

1. Turn power on, replace fuse or reset breaker.

3. Motor reversing switch not 

engaged.

3. Push switch firmly right or left. Fan will not 

operate when switch is in the middle.

4. Pull chain switch not "on". 4. Pull switch chain.

1. Wrong wire connection.

1. Refer to Step 1, page 10 to ensure all wire 

connections were done correctly.

2. Bulb is burned out.

2. Replace the bulbs.

Light does not work.

Fan does not start

2b. Check the plug connection in the switch 

housing.

2a. Turn power off and loosen canopy; check 

all connections according to section WIRING 

INSTRUCTIONS on page 10.

2. Loose wire connections or 

wrong connections.

PROBLEM

PROBABLE CAUSE

CORRECTIVE ACTION

6. Blade holders are loose.

6. Check to be sure the fan blade irons seat 

firmly and uniformly on the surface of the motor. 

If flanges are seated incorrectly, loosen the 

flange screws and retighten.

7. Blade out of balance.

7. Interchange two adjacent blades; this will 

redistribute the weight and possibly result in 

smoother operation. Or, refer to the instructions 

inside the balance kit (Q).

Summary of Contents for CPJ1240



















Reviews: