background image

5

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the 

product.
• 

Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit 

breakers.

•  Make sure all electrical connections comply with local codes, ordinances, the National Electrical 

Code and ANSI/NFPA 70-199. Hire a qualified electrician or consult a do-it-yourself wiring 

handbook if you are unfamiliar with installing electrical wiring.

•  Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to 

the floor and at least 30 in. from the end of the blades to any obstruction.

•  The net weight of this fan is: 26.03 lb (11,81 kg).

DANGER:

 When using an existing outlet box, make sure the outlet box is securely attached to 

the building structure and can support the full weight of the fan. Failure to do this can result in serious 

injury or death. The stability of the outlet box is essential in minimizing wobble and noise in the fan 

after installation is complete.

WARNING:

 To avoid personal injury, the use of gloves may be necessary while handling fan 

parts with sharp edges.

WARNING:

 Using a full-range dimmer switch to control fan speed will cause a loud humming 

noise from the fan. To reduce the risk of fire or electric shock, do NOT use this fan with any solid-state 

speed control device.

WARNING: 

To reduce the risk of fire, electric shock or personal injury, mount the fan to an outlet 

box marked “ACCEPTABLE FOR FAN SUPPORT” and use the mounting screws provided with the 

outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable 

for fan support and may need to be replaced. Consult a qualified electrician if in doubt. Secure the 

outlet box directly to the building structure. The outlet box and its support must be able to support the 

moving weight of the fan (at least 35 lbs.). 

WARNING: 

To reduce the risk of fire, electric shock or personal injury, wire connectors provided 

with this fan are designed to accept only one12-gauge house wire and two lead wires from the fan. If 

your house wire is larger than 12-gauge and/or there is more than one house wire to connect to the 

two fan lead wires, consult an electrician for the proper size wire connectors to use.

WARNING: 

To reduce the risk of fire, electric shock or personal injury, do not bend the blade 

arms when installing them, balancing the blades or cleaning the fan. Do not insert objects between 

the rotating fan blades.

WARNING: 

To reduce the risk of personal injury, use only parts provided with this fan. The use 

of parts OTHER than those provided with this fan will void the warranty.

Summary of Contents for 42612




















Reviews: