Harbinger LV7, Owner'S Manual

Page: 4 / 9

LV7 OWNER’S MANUAL LV7 OWNER’S MANUAL
6 7
16
17
18
19
20
21
22
23
LV7 TOP PANEL
1
2 3 4
5
9
10
12
11
13
6
7
8
1
MIC / LINE INPUT
An XLR or 1/4” microphone or line level source can be connected here
2
1/4” INPUTS
CH2|3 – Connect a passive guitar signal (mono or stereo) or a mono
or stereo line-level signal here
CH3|4 – Connect a mono or stereo line-level signal here
3
CH 6|7 STEREO INPUT
Connect a phone, tablet or laptop here. The level for this input is
controlled by
17
4
REC OUT
Connect this output to a recording device with a stereo 1/8” (3.5 mm)
input. This signal is taken from the MAIN bus.
5
XLR MAIN OUTPUTS
The signal at this output contains the entire mix of input signals.
Connect this output to the inputs of powered speakers, a power amp
or recording interface, via XLR cable
6
HEADPHONE OUTPUT
Connect headphones here and control level with
19
. This signal is the
same as that being sent to the MAIN bus
7
48V PHANTOM POWER BUTTON
Activates phantom power which will send a 48V Charge to the XLR input
connection on CH1, required for condenser type microphones.
CAUTION: Leave this switch turned off if phantom power is not
required. In order to prevent noise and possibly damaging connected
devices please follow these instructions:
• Leave 48V phantom power off when connecting a device that does not
require it
• Do not plug or unplug any connections to CH1 of the LV7 when 48V
phantom power is on
•
Before turning on or off 48V phantom power make sure the CH1 level
control is turned all the way down (to the left-most position)
8
80Hz HIGH-PASS FILTER
Reduces low frequency “rumble” from microphone signals
9
GUITAR HI-Z BUTTON
Changes the impedance on CH2|3 to optimize passive guitar
and bass signals
10
HIGH EQ CONTROL
Boosts or cuts the high frequencies of the CH1 input at a corner
frequency of 10 kHz
11
CH 1 GAIN CONTROL
Adjusts the preamp gain of channel 1
LV7 REAR PANEL
BLUETOOTH
®
PAIRING, TROUBLESHOOTING
LED STATE AND BLUETOOTH STATUS
LED is Off - Bluetooth is off
LED is Blinking - Bluetooth is ready to pair
LED is solidly lit - Bluetooth is actively paired with a source device
If the pair LED is in an off state, press the LV7’s BLUETOOTH PAIR button to
initialize Bluetooth and activate pairing mode (the pair LED will start blinking).
Scan for available Bluetooth devices on your phone, tablet or PC. Locate
and select “Harbinger Mixer” to activate pairing. When actively paired, the
LV7’s pair LED will become solidly lit.
If another device is already actively paired press the PAIR button to clear the
active pairing.
Pressing and holding PAIR disables Bluetooth.
• On your Apple iOS device
1. Power off the LV7 and leave it off
2. Open Settings app, select Bluetooth
3. If “Harbinger Mixer” is listed under MY DEVICES, touch info button,
tap to Forget This Device
4. Turn off Bluetooth, wait 10 seconds, turn on Bluetooth
• On your Android device
1. Power off the LV7 and leave it off
2. Open Settings, select Bluetooth
3. If “Harbinger Mixer” is listed under Paired Devices, touch gear Icon,
and tap to Unpair
4. Turn off Bluetooth, wait 10 seconds, turn on Bluetooth
1
DC POWER INPUT
Connect only the included power adapter to this input
2
POWER SWITCH
Switches power on/off to the mixer
1
2
• Then power on your LV7 and press PAIR (the pair LED should flash)
• You should now be able to connect to LV7 via Bluetooth
These steps should resolve any Bluetooth trouble you may encounter:
14
15
12
LOW EQ CONTROL
Boosts or cuts the low frequencies of the CH1 input at a corner
frequency of 100 Hz
13
CH1 PAN CONTROL
Adjusts positioning of the CH 1 signal within the stereo sound field
14
CLIP INDICATOR LED
Lights red when the signal level at the preamp stage is too high and
causing clipping/distortion.
15
CH LEVEL CONTROLS
Adjusts the relative level of the associated channel being sent to
the MAIN bus
16
BLUETOOTH PAIR BUTTON
With no actively paired device, pressing this button will activate pairing
mode (LED will start blinking).
With a device actively paired (LED lit solidly), pressing this button will
cancel the pair and will activate pairing mode (LED will begin blinking
Pressing and holding this button will cancel any active pair and turn
Bluetooth off (LED will turn off)
17 BLUETOOTH / CH 6|7 LEVEL CONTROL
Controls the relative level of the BLUETOOTH and CH 6|7 input signals
being sent to the MAIN bus
18
BLUETOOTH /CH 6|7 SOLO BUTTON
Mutes all input sources except BLUETOOTH and CH 6|7 signals
19
HEADPHONE LEVEL CONTROL
Controls the level of the headphone signal
20
CH 2 | 3, 4 | 5 BAL CONTROLS
Adjusts the stereo balance of the associated stereo input signal. If the input
signal is mono, the BAL control acts as a pan control. See
13
21
STEREO/MONO BUTTON
Switches the MAIN out signal between mono and stereo operation.
Out position = stereo, in position = mono
22
MAIN OUTPUT LEVEL METERS
Displays the MAIN mix output level
23
MAIN OUTPUT LEVEL CONTROL
Controls the level of the MAIN output. The unity gain position on this
volume control is indicated with a shaded in segment on the surrounding
knob graphic. At the unity gain setting no additional volume boost or cut is
being added to the main output signal.