background image

4_ safety information

Safety information

8.  If any unusual smells or smoke come from the unit, stop using the product. in such case, 

immediately disconnect the power source and contact the service center. continued use in 
such a condition may cause fire or electric shock.

9.  If this product fails to operate normally, contact the nearest service center. never disassemble 

or modify this product in any way. (Hanwha Vision is not liable for problems caused by 
unauthorized modifications or attempted repair.)

10. When cleaning, do not spray water directly onto parts of the product. doing so may cause fire 

or electric shock.

CAUTION

1.  Do not drop objects on the product or apply strong shock to it. Keep away from a location 

subject to excessive vibrationor magnetic interference.

2.  Do not install in a location subject to high temperature, low temperature, or high humidity. 

Doing so may cause fire or electric shock.

3.  If you want to relocate the already installed product, be sure to turn off the power and then 

move or reinstall it.

4.  Remove the power plug from the outlet when then there is a lightning. Neglecting to do so 

may cause fire or damage to the product.

5.  Keep out of direct sunlight and heat radiation sources. It may cause fire.
6.  Install it in a place with good ventilation.
7.  Avoid aiming the camera directly towards extremely bright objects such as sun, as this may 

damage the CMOS image sensor.

8.  Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, 

such as vases, shall be placed on the apparatus.

9.  The Mains plug is used as a disconnect device and shall stay readily operable at any time
10. Do not expose the camera to radioactivity. Radioactivity exposure may damage the CMOS.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 
conditions :

1) This device may not cause harmful interference, and
2) This device must accept any interference received including interference that may cause 

undesired operation.

Summary of Contents for HCF-8011RV

































Reviews: