background image

HPS-BPWDMXLED QUATTRO

 

 

   

Hanson

 

ProSystems

 

 

www.hansonprosystems.com

 

User

 

Manual

 

Page

 

11 of

 

28

Power Linking:

 

The fixture provides power linking via the power con outputs located in the back of 

the fixture. Please see the diagram below for further explanation. 
 

 

 

You can power link up to ten (10) QUATTRO fixtures on a 120 VAC, 20 AMP or up to twenty 
(20) QUATTRO fixtures on a 240 VAC, 20 AMP circuit.   

 

 

The power linking diagram shown above corresponds to the North American version of the 
fixture ONLY! If using the fixture in other markets, you must consult with the local Hanson 
ProSystems dealer or distributor because power linking connectors and requirements may 
differ in your country or region. 

 

DMX Wire Setup:

 Set the fixture in DMX mode to control with a DMX controller.   

 
1. Connect the fixture to a suitable power outlet or use internal battery. 
2. Turn the fixture on. 
3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input on the fixture. 

DMX Wire Linking:   

1. Make sure previous step on DMX wire setup is done already. 
2. From the DMX output of the first fixture run a DMX cable to the DMX input of the second fixture. 
3. Repeat step 2 for each fixture you wish to use. 
 

 

To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable 
path possible. The order in which fixtures are connected in a DMX line does not influence the DMX 
addressing. For example, a fixture assigned a DMX address of 1 may be placed anywhere in a DMX 
line, at the beginning, at the end or anywhere in the middle. When a fixture is assigned a DMX address 
of 1, the DMX controller knows to send DATA assigned to address 1 to that fixture, no matter where it is 
located in the DMX chain. 
 
 

HPS-BPWDMXLED QUATTRO

 

 

 

Hanson

 

ProSystems

 

www.hansonprosystems.com

User

 

Manual

 

Page

 

12 of

 

28

DMX Signal Indicator

:

 

When menu display screen is locked the red dot in LED display will blink, 

indicating DMX signal. If the red dot is not blinking the unit is indicating that there is no DMX signal.   

 

Mounting:

 

Before mounting the fixture, read and follow the safety recommendations indicated in the 

rigging section below. The QUATTRO may be mounted in any position; however, make sure there is 
adequate ventilation around the fixture to prevent overheating. 

Rigging: 

 

Before deciding on a location for the fixture, always make sure there is easy access to the 
fixture for maintenance and programming purposes.   

 

Make sure that the structure or surface onto which you are mounting the fixture can support 
the fixture weight. Refer to the Technical Specifications

 

section of this manual for weight 

information. When mounting the fixture overhead, always use a safety cable. Mount the fixture 
securely to a rigging point, whether an elevated platform or a truss. 

 

When rigging the fixture onto a truss, you should use a mounting clamp of appropriate weight 
capacity. The bracket has holes, which is appropriate for this purpose. 

 

When power linking multiple fixture, you must always consider the length of the power linking 
cable and mount the fixture close enough for the cable to reach.   

 

The bracket adjustment knobs allow for directional adjustment when aiming the fixture to the 
desired angle. Only loosen or tighten the bracket knobs manually. Using tools could damage 
the knobs. 

 

The double-bracket yoke on the ORIGINAL also serves as a floor support or allows for surface 
mounting. When using the fixture on the floor tighten the bracket adjustment knobs firmly to 
keep bracket secure. Make sure that the fixture and cables are away from doorways, people 
and vehicles. 

 

Summary of Contents for HPS-BPWDMXLED QUATTRO

















Reviews: