Assembly see page 31
Fault
Cause
Remedy
Insufficient water
-
Supply pressure inadequate
-
Check water pressure (If a pump has been installed
check to see if the pump is working).
-
Filters are dirty (96922000)
-
Clean filter in front of the mixer and on the MTC-
thermo cartridge (96922000)
-
Shower filter seal dirty
-
Clean filter seal between shower and hose
Crossflow, hot water being forced into cold water
pipe, or vice versa, when mixer is closed
-
Backflow preventers dirty or leaking
-
Clean backflow preventers, exchange if necessary
Spout temperature does not correspond with
temperature set
-
Thermostat has not been adjusted
-
Adjust thermostat
-
Hot water temperature too low
-
Increase hot water temperature to 42 ºC to 65 ºC
Temperature regulation not possible
-
thermo cartridge calcified
-
Exchange thermo cartridge
Shower or spout dripping
-
Dirt or sedimentation on valve seat, shut-off unit
damaged
-
Clean or exchange shut-off unit
Instantaneous heater didn't work with thermostat
-
Ecostop safety set removed.
-
Remove Ecostop safety set (95042000)
-
Flow limiter in handshower isn’t removed
-
Remove flow limiter
-
Filters are dirty
-
Clean the filter / exchange filter
-
Non return valve hasn't moved back
-
Exchange non return valves
Cleaning
see enclosed brochure.
Test certificate
(see page 36)
Spare parts
(see page 36)
Flow diagram
(see page 35)
Shower
Bath tub
Dimensions
(see page 35)
Operation
(see page 34)
Maintenance
(see page 33)
• To guarantee the smooth running of the thermostat, it is necessary
from time to time to turn the thermostat from total hot to total cold.
• The mixer is equipped with non return valves. The non return
valves must be checked regularly according to DIN EN 1717 in
accordance with national or regional regulations (at least once a
year).
ECOSTOP
(see page 33)
Adjustment
(see page 32)
After the installation, the output temperature of the thermostat must be
checked. A correction is necessary if the temperature measured at the
output differs from the temperature set on the thermostat.
Safety Function
(see page 32)
The desired maximum temperature for example max. 42º C can be pre-
set thanks to the safety function.
Do not use silicone containing acetic acid!
Symbol description
Safety Notes
Gloves should be worn during installation to prevent crushing and cutting
injuries.
The shower system may only be used for bathing, hygienic and body cleansing
purposes.
Children as well as adults with physical, mental and/or sensoric impairments
must not use this shower system without proper supervision. Persons under the
influence of alcohol or drugs are prohibited from using this shower system.
The hot and cold supplies must be of equal pressures.
Installation Instructions
• Prior to installation, inspect the product for transport damages. After it has been
installed, no transport or surface damage will be honoured.
• The product is not designed to be used with steam baths!
• The fitting must be installed, flushed and tested after the valid norms!
Thermostatic mixer in conjunction with combination boilers
• If fitting a hand shower remove the water limiter from the shower.
• If the continuous water heater causes any problems, or you have different
water pressures you must install a water limiter to the cold supply, (ordered
separately,article number 97510000).
• Thermostatic mixer Shower: When using the Ecostat with combination boilers, the
Ecostop safety set (95042000) has to be removed.
Technical Data
Operating pressure:
max. 1 MPa
Recommended operating pressure:
0,1 - 0,5 MPa
Test pressure:
1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature:
max. 80°C
Recommended hot water temp.:
65°C
Thermal disinfection:
max. 70°C / 4 min
anti-pollution function
The product is exclusively designed for drinking water!
English
Special information for UK
(see page 37)
4
