background image

14

15

Thermostatic Adjustment 

Temperature Limitation 

The temperature is limited by the safety stop to 40°C. 

If a higher temperature is required, it is possible to 

over ride the safety stop by depressing the cross 

handle. 

NB.

 It is recommended that for 

private domestic 

use

 the maximum mixed water temperature be set 

at the following factory set values:

 

Shower Mixer 43°C

 

Bath/Shower 46°C

Temperatures can be set by following the procedures 

under 

„Setting  thermostat  to  a  maximum 

temperature“. 

This  ensures  that  after  correct 

installation the outlet temperature of the water can 

never exceed 43°C.

To guarantee a smooth running of the thermostatic 

element,  it  is  necessary  from  time  to  time  to  turn 

the  thermostat  from  total  hot  to  total  cold.  The 

thermostatic mixer valve should be checked annually 

by a qualified person to ensure correct operation.

The mixer is fitted with check valves (page 18 pos. 

7)  and  filters  on  the  thermostatic  element.  If  the 

water  flow  drops  the  filters  need  to  be  cleaned. 

For that purpose the mixer has to be removed from 

the wall.

 

Calibrating Thermostat 

1.  If  the  temperature  reading  is  different  to  the 

showering  temperature,  turn  the  thermostat 

handle until a 40°C reading is shown on your 

thermometer (fig.1). 

2.  Remove the handle end cap, undo the screw and 

pull off the handle and safety set disk (fig.2). 

3.  Rotate the cross handle so the marking point is 

positioned at 12 o clock (fig. 3) and re-fit onto 

the spindle. Replace the screw (fig.4). 

1

2

3

4

40°

SW 3 mm

Summary of Contents for Axor Terrano 37670 Series





















Reviews: