background image

 

13

Step 5- Stick the conversion label on the rating plate as shown in Figure 15. 

Metal Rating Plate

 

 

1. 

 

2. 

 

3. 

 

4. 

 

5. 

 

6. 

 

7. 

 

 

 

Figure 15              Conversion Label  

 

                               

                                 

 

LIGHTING INSTRUCTIONS

 

Warning: If these instructions are not followed exactly, a fire or explosion may 
result causing property damage, personal injury or loss of life. 
1. Make sure the control knob is in the "OFF" position. See Figure 16 Open the 
tank                                                                                                                                                               
valve all the way. 
 

 

 
IGNITER BUTTON                                                                CONTROLKNOB 

 
 
2. Push in the igniter button. You will hear a slight clicking sound. With the 
igniter button pushed in, push and turn the control knob to the “ON” position. 
the fire should light within a few seconds. Once the flame is lit, release the 
igniter button and continue to hold the 

Serial Number _________________ 

 

 

 

Model Number: 98900

CAUTION: 

The gas pressure regulator provided with this appliance must be used. This regulator is set for an outlet pressure of   

 
 
 

 

 
Minimum clearance from combustible constructions: Sides: 24 in.609 mm. Top 72 in. 1828 mm.

 

FOR OUTDOOR USE ONLY. 

If stored indoors, detach and leave cylinder outdoors.   

This appliance has been converted to use Natural Gas. Input 40,000 Btu/hr. 

Max Gas Supply Pressure 7 inch w.c. (1.74 kPa) Min. Gas Supply Pressure 5 inch w.c. (1.24 kPa) 

Figure 16

 

Summary of Contents for Traditions TRAD5PCFPBR-RED


















Reviews: