manualshive.com logo in svg

Hanna Instruments HI 84181, Instruction Manual, Page: 16 / 20

Share
Download
Hanna Instruments HI 84181 Instruction Manual Download Page 16

16

PREPARATION PROCEDURE
Preparation of potassium electrode:

• Remove the protective cap from the 

HI 61014

 potassium sensor’s tip.

• Screw the potassium cell into the electrode body. Ensure the Sealing Ring is installed before

screwing.

• Due to shipping or storage the internal solution inside the sensing modules may have

developed an air pocket near the membrane. Gently shaking the sensor down (like the old

style mercury thermometers) will place the internal solution next to the membrane.

• Soak in potassium standard 10

-2

 M for at least half-hour before measurements in order to

optimize the sensor response.

ELECTRODE CONDITIONING & MAINTENANCE

FUSE REPLACEMENT

To change the fuse follow next steps:
• Disconnect the power cord from the rear panel of the

instrument.

• Pull out the fuse holder located near the power cord

connector.

• Replace the fuse with a similar one.
• Push the fuse holder with the fuse in the appropriate place.

Summary of Contents for HI 84181





















Reviews:

No comments