manualshive.com logo in svg

Hanna Instruments edge EC HI2003, Manual, Page: 29 / 39

Share
Download
Hanna Instruments edge EC HI2003 Manual Download Page 29

Operational Guide

29

If  enabled,  the  number  of  days  since  the  calibration 
expired. (i.e. “CAL EXPIRED 2 DAYS AGO”).

The serial number of the probe.

Note

: Press GLP at any moment and the instrument will return to measurement 

mode.

The RANGE key will change measurement from conductivity to TDS to Salinity.

Conductivity Measurements

Connect the conductivity probe to the instrument and 
wait until probe parameters are loaded. The following 
message  is  then  displayed  on  the  LCD:  “PROBE 
CONNECTED”.

Verify  if  the  probe  has  been  calibrated.  Suspend  the  probe  into  the  solution 
to be tested. The sleeve holes must be completely submersed. Tap the probe 
repeatedly to remove any air bubbles that may be trapped inside the sleeve.

The  conductivity  value  will  be  displayed  on  the  fi rst 
LCD line, the temperature on the second LCD line and 
calibration  or  range  specifi c  information  on  the  third 
LCD line.

To toggle between information displayed on the third LCD line, use the ARROW 
keys.
If the reading is out of range when the range is set to 
automatic, the full-scale value (200.0 mS/cm for ATC 
mode or 500.0 mS/cm for absolute conductivity) will 
be displayed blinking.

Note

:  Temperature-compensation  and  absolute  conductivity  (NoTC)  are 

selected in the SETUP confi guration.

Automatic  Temperature  Compensation  (ATC)

:  The  conductivity  probe  has 

a built-in temperature sensor; the temperature value is used to automatically 
compensate  the  EC/TDS  reading.  When  this  option  is  selected,  “ATC”  tag  is 
displayed. A temperature coeffi

    cient for the sample must also be set.

NaCl % GLP 
Information

EC/TDS 
Measurements

Summary of Contents for edge EC HI2003








































Reviews:

No comments