background image

5.

Safety instructions:

-

The Implements may only be used when all safety mechanisms are in place and
fully functional.

-

All faults capable of impairing safety must immediately be remedied by specialist
personnel.

-

The operating instructions of any additional attachments installed must be read
through carefully and observed.

-

Never climb onto the tractor or leave it unattended when the p.t.o. shaft is running.

-

Never allow anyone who is not familiar with the safety and operating instructions to
use the machine.

-

Remove all visible large objects which may be picked up and hurled aside by the
rotary power harrow. Particular attention must be paid to loose wires on the ground.

-

Adjust your driving speed in line with the ground conditions and prevailing
circumstances.

-

No one may remain within 10 meters of the power harrow during operation of the
machine. High risk of injury due to moving machine parts and objects being hurled
away from the machine, such as stones, etc.

-

Never climb or reach in between the power harrow and the tractor with your arms or
legs during operation of the machine – high risk of injury! (This is only permitted
when the machine has been lowered to the ground and the tractor switched off.)

-

The machine should only be operated in full daylight . Traffic regulations must be
observed when driving on public roads. Adequate illumination must be ensured when
driving in twilight or darkness (A detachable set of lights is recommended.)

-

Never climb or reach in between the support roller and cutter unit with your arms or
legs – high risk of injury.

-

Always wear tightly fitting clothes so that these cannot be caught between rotating
parts of the machine.

-

Safety stickers must be kept clean and observed!

-

Never open or remove the guard elements during operation. Worn or defective parts
must immediately be replaced by new parts.

8

Summary of Contents for 1BQ1.3

















Reviews: