Hangar 9 CAP 232G ARF Assembly Manual Download Page 25

Page: 25 / 36

Section 8 – Engine Installation

Required Parts

•.Fuselage.

•.1/4-20.x.1".bolts.(4)

•.17".throttle.pushrod.tube. •.1/4".fuel.tubing
•.Nylon.clevis.

•.1/4".split.washers.(4)

•.13

".throttle.pushrod.

•.Cowling

•#4.washer.(4).

•.1/4".fuel.tube.(4)

•.Clunk.(fuel.pickup).

•.Metal.caps.(2)

•.Fuel.tubing.

•.Fuel.tank

•.Rubber.stopper.

•.M3.x.20.screw

•.15".(380mm).tie.wrap
•.4-40.x.1".socket.head.screw.(4)
•.Metal.tubes.(short.and.long)

Required Tools and Adhesives

•.Medium.CA.

•.Drill

•.Ruler.

•.Square

•.Hobby.knife.

•.Razor.saw

•.Foam:.1/4".(6mm)
•.Rotary.tool.with.sanding.drum
•.Drill.bit:.5/32".(4mm),.7/32".(5.5mm)
•.3

".(83mm).spinner.and.adapters

•.Phillips.screwdriver



Step 1

Attach.the.engine.standoff.onto.the.engine.using.the.

instructions.provided.with.the.engine..Also.collect.all.the.

items.required.for.the.exhaust.system.at.this.time.



Step 2

Attach.the.engine.to.the.firewall.using.the.hardware.

provided.with.your.engine.from.the.inside.of.the.firewall..

Mount.the.muffler.to.the.engine.



Step 3

Determine.the.proper.location.for.the.throttle.pushrod..

Mark.the.location.with.a.felt-tipped.pen..Remove.the.

engine.and.drill.the.firewall.for.the.pushrod.tube.using.a.

drill.and.5/32".(4mm).drill.bit..Roughen.the.tube.using.

medium.sandpaper..Slide.the.tube.into.position.and.use.

medium.CA.to.glue.it.to.the.firewall.



Step 4

Trim.the.tube.1/2".(13mm).in.front.of.the.throttle.servo.

tray..Place.a.1/4".(6mm).piece.of.fuel.tubing.onto.a.clevis,.

then.thread.the.clevis.onto.the.13

".(350mm).throttle.

pushrod..Attach.the.clevis.to.the.carburetor.arm..Use.a.

brass.connector.to.connect.the.throttle.pushrod.to.the.

servo.arm.as.shown.

Summary of Contents for CAP 232G ARF





































Search results

Summary of Contents for CAP 232G ARF

Reviews:

Related manuals for CAP 232G ARF

Brands by name

Popular brands

Hangar 9 CAP 232G ARF, Assembly Manual

Search results

Summary of Contents for CAP 232G ARF

Reviews:

Related manuals for CAP 232G ARF

Brands by name

Popular brands