Hangar 9 CAP 232G ARF Assembly Manual Download Page 21 | Manualshive

Page: 21 / 36

background image

21



.

Step 4

Repeat.Step.3.for.the.second.cable..Tape.the.cables.to..

the.rudder.servo.tray.to.keep.them.from.moving.around.

inside.the.fuselage.



.

Step 5

Prepare.the.rudder.servo.arm.by.attaching.two.4-40.ball.

links.using.the.standoffs.and.4-40.lock.nuts.
Using.the.screws.included.with.the.servos,.fasten..

the.servos.in.place..You.may.find.it.helpful.to.drill..

1/16".(1.5mm).pilot.holes.before.installing.the.screws..

Center.the.rudder.servo.and.place.the.servo.arm.onto..

the.servo.



.

Step 6

Adjust.the.position.of.the.threaded.end.on.the.cable.so.

it.will.thread.into.the.ball.end.and.have.slight.tension.on.

the.cable.to.the.rudder..It.will.take.some.time.to.get.the.

position.right..Once.the.position.of.the.end.is.correct,.

pass.the.cable.back.through.the.crimp.and.secure.the.

cable..Thread.the.end.into.the.ball.end..Repeat.this.for.

both.cables.

Note

:.The.cables.will.cross.inside.the.

fuselage.to.get.the.correct.geometry.



.

Step 7

With.the.radio.on,.check.the.operation.of.the.rudder..

Adjust.the.cables.so.when.the.rudder.servo.is.centered,.

the.rudder.is.centered.as.well..There.will.be.tension.on.

the.cables..Adjustments.can.be.made.at.the.rudder.control.

horn.and.at.the.servo.arm..Once.adjustments.are.made,.

secure.the.servo.arm.to.the.rudder.servo.using.the.screw.

that.came.with.the.servo.

Note

:.Check.the.tension.of.the.rudder.

cables.before.every.flying.session,.

as.they.may.stretch.over.time.

Section 6A – Rudder Servo Installation: Pull-Pull

«
...
19
20
21
22
23
...
»

Summary of Contents for CAP 232G ARF





































Reviews:

No comments

Related manuals for CAP 232G ARF

Brand: Lionel Pages: 4

Brand: LEGO Pages: 64

Brand: marklin Pages: 12

Steaman Aerobatic Biplane

Brand: REVELL Pages: 12

STAR WARS 75102

Brand: LEGO Pages: 124

SAMMIE & BERTIE

Brand: roundhouse Pages: 20

Alphabert s Pen Pal Phonics

Brand: VTech Pages: 16

Brand: Zapf Creation Pages: 56

Fordhampton Garden center

Brand: GAUGEMASTER Pages: 4

Brand: beeloom Pages: 11

Brand: Stevens AeroModel Pages: 29

Starbeans Coffee Shop

Brand: Great Little Trading Pages: 6

WILD THINGS Series

Brand: Fischer-Price Pages: 2

Brand: Multiplex Pages: 20

Brand: Eduard Pages: 4

M 1 A1 (HA) ABRAMS

Brand: REVELL Pages: 10

EI-2309 Language Tutor

Brand: Educational Insights Pages: 8

Brand: PARKZONE Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands