background image

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE INVERSION TABLE.

WARNING

!

SAVE THESE INSTRUCTIONS

WARNING

 - To reduce the risk of injury to persons: 

•  Read and understand all the instructions, review all other accompanying documents, and inspect the equipment before using the inversion
    table. It is your responsibility to familiarize yourself with the proper use of this equipment and the inherent risks of inversion, such as falling on your head or neck,
    pinching, entrapment, or equipment failure. It is the responsibility of the owner to ensure that all users of the product are fully informed about the proper use of the
    equipment and all safety precautions.
•  Close supervision is necessary when the inversion table is used near children, or by or near invalids or disabled persons.
•  Use the inversion table only for its intended use as described in this manual. 

DO NOT

 use attachments not recommended by the manufacturer.

•  

NEVER

 drop or insert any object into any opening.

•  

DO NOT

 use or store product outdoors.

•  

DO NOT

 use if you are over 6 ft 6 in (198 cm) or over 250 lbs. (113 kg).  Structural failure could occur or head/neck may impact the fl oor during inversion.

•  

DO NOT

 allow children to use this machine.

•  Keep children, bystanders, and pets away from machine while in use.
•  Keep body parts, hair, loose clothing and jewelry clear of all moving parts.
•  The inversion table has no user serviceable parts.
•  This product is intended for indoor home use only.

 DO NOT 

use in any commercial, rental or institutional setting.

•  

DO NOT

 use the equipment without a licensed physician’s approval and a review of the medical contraindications, as noted in the Owner’s Manual. 

•  Failure to assemble and/or use the equipment as directed may void the manufacturer’s warranty on this product and could result in injury or death.
•  Choose a level surface for assembling and operating the table.
•  Follow each step in sequence. 

DO NOT

 skip ahead.  

•  Make sure that all fasteners are secure.
•  

ALWAYS

 test and inspect the table. Make sure the table rotates smoothly to inverted position and back.

•  

ALWAYS 

replace defective components immediately and/or keep the equipment out of use until repair.

FAILURE TO FOLLOW INSTRUCTIONS AND WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH.

BEFORE YOU BEGIN:

 Review all steps before beginning assembly and read all precautions before using the inversion table. Carefully adhere to the Assembly  

 

   

 

     Instructions and Owner’s Manual to help ensure safety and product integrity. 

Summary of Contents for SR 250














Reviews: