Hang ups Teeter EP-950 Assembly Instructions Manual Download

Page: 3 / 11

You should have all of the items listed below. If you have any questions on assembly, contact Customer Service at 1-800-847-0143.

A-Frame

EZ-Angle

™

Tether Strap

Attached to A-frame

Main Shaft w/Ankle System

Ergo Embrace Cups (4)

Table Bed Assembly

Bolt Set

Bolts

Washers

Nuts

Head Pillow

Over EZ

™

Handles

Right Handle

Left Handle

Threaded Bolts (4)

Shrouds

1/4” Bolts

Roller Hinges w/Traction Handles

Wrenches (2)

Allen Wrench (1)

EP-1100

F5-1008

NX-1630

EP-1054

EP-1140

EP-1149

EP-1149-B

EP-1149-D

EP-1149-A

EP-1105

GL-9522

GL-9518

GL-9523

GL-9524

GL-9525

TR-1003

F5-1088

EP-1128-A

ITEMS FOR ASSEMBLY

ITEM NUMBER

NX-1630

Items for Assembly

TR-1003

F5-1088

EP-1100

F5-1008

EP-1140

GL-9518

GL-9522

GL-9524

GL-9525

GL-9523

EP-1128-A

EP-1149

EP-1105

Bolts will come pre-assembled in handles and shrouds.

Summary of Contents for EP-950












Search results

Summary of Contents for EP-950

Reviews:

Related manuals for EP-950

Brands by name

Popular brands

Hang ups Teeter EP-950, Assembly Instructions Manual

Search results

Summary of Contents for EP-950

Reviews:

Related manuals for EP-950

Brands by name

Popular brands