![background image](http://html1.mh-extra.com/html/hands/rr-420-evo/rr-420-evo_operators-manual_3070934018.webp)
18
11
12
D. OPERATION and USE
D1 Working configuration
The windrow rotary rake will be driven on to the
work place, according to the regulations
described in paragraph B2 and before using the
equipment, the operator will perform the
following interventions:
-
make certain that the PTO is disengaged;
IMPORTANT
Tractor PTO must never be engaged with
the engine switched off;
-
only for the mounted type:
by activating
the relative lever, lower the tractor hydraulic
lift until the wheels of the windrow rotary
rake touch the ground;
-
switch off the tractor engine, engage the
parking brake, remove the ignition key from
the dashboard and go down from cabin;
-
provide to put the equipment in the working
configuration (
fig.17
):
a. one at a time, remove tine-holder arms
(
2
) from the respective supports on
frame (
1
) and place them in the
housings on work rotating unit (
3
) to
then block them by using safety pin (
4
);
b. first on the right side and then on the left
one: pull forward the side protection
screen towards tractor connection (
6
),
so to unhook it from the mechanical
block for transportation (
5
);
c. keeping
it
also
pulled,
rotate
it
downwards, as indicated in figure (
7
),
and release it only when the same is
placed on the frame so to be blocked by
its relative work mechanical block (
9
).
When the screen (
8
) is released,
appropriate spring (
10
) will take it back
to the initial position;
d. on the left side, before lowering
completely the protection screen, open
the side deflector (
fig.18
). Therefore,
remove the safety pin from the pin that
blocks the deflector rotation. Remove
the pin from its housing (
11
) and rotate
deflector (
12
) of 90° upwards, as
indicated in the figure. Complete
lowering the side protection screen.
Note:
on this side of the windrow rotary
rake, the mechanical block is not set.
The side deflector weight keeps the
screen position during the process;
e. make certain that the bearing foot is in a
safety position. It must be already in this
4
5
6
7
8
9
10
3
1
2
Fig.17
Fig.18
Summary of Contents for RR 420 EVO
