10
Moving on fields:
inside them
the machinery
must not activate any luminous signal or buzzer
or display any type of panel. The windrow rotary
rake must assume the
working configuration
only before operating.
Working configuration
(both mounted and pull-
type -
fig.5
):
-
one at a time, remove tine-holder arms (
2
)
from respective supports on frame (
1
) and
place them in each housings on work rotating
unit (
3
) to then block them by using safety pin
(
4
);
-
first from a side and then from the other: pull
forward, towards tractor connection, the side
protection screen (
6
), so to unhook it from the
mechanical
block
(
5
)
by
using
for
transportation;
-
keeping it still pulled, rotate it downwards, as
indicated in figure (
7
), and release it only
when it is placed on the frame so to be
blocked by its relative work mechanical block
(
9
). When the screen (
8
) is released, an
appropriate spring (
10
) will takes it back to
the initial position.
Note:
on the left side of
the windrow rotary rake, the mechanical
block is not set. During the process, the side
deflector weight keeps the side screen in
position;
-
for the use and the relative operating
adjustments,
to
consult
the
following
paragraph.
B.3 Intended use and warning of employ
The windrow rotary rake is an agricultural
equipment used to harvest any other type of
previously
cut
forage,
with
formation
of
windrows.
The rake can be either mounted or pull-type. The
mounted
type can work only if installed on any
agricultural
tractor
equipped
with
3-point
universal hitch and hydraulic lift. Whereas, the
pull-type
must be connected to the towing hook
installed behind each tractor. The operation is
common for both types and it is obtained both by
effect of the tractor towing
and by effect of the
rotation of them working units. This rotation is
provided by a cardan shaft coupled to the tractor
PTO. The arm rotating motion and the action of
tines allow to realise even and well ventilated
windrows.
On the
pull-type
rake there are two hydraulic
cylinders, which operation allows to adjust the
tine adaptation to the ground and to lift them for
the tractor change of direction at the end of the
field or in reverse. These cylinders are powered
by the tractor auxiliary hydraulic circuit, through
hoses equipped with quick couplings and
controlled by a special lever placed inside the
cabin.
The windrow rotary rake must be used only by
adult, qualified and trained personnel and aware
of the instructions contained in this manual.
Safety is of prime importance for the personnel
who use the equipment or who perform repairs
or maintenance. Given that the provided
instructions cannot cover all possible working
situations and related danger, personnel should
always use caution and common sense.
Before starting the tractor and begin working,
it is important:
-
verify that the equipment has been correctly
installed on the tractor;
-
verify that all locking and safety devices are
present and undamaged;
TRANSPORT CONFIGURATION WORKING CONFIGURATION
4
5
6
7
8
9
10
3
1
2
Fig.5
Summary of Contents for RR 420 EVO
