H&S HD, Operator'S Manual / Parts Book

Page: 41 / 54

CROSS CONVEYOR
ADJUSTMENT
Proper tension should be maintained on the
auger wipers and hold downs when operating
forage box. To adjust wipers and hold downs,
start with rear auger first. Loosen bolts (A)
securing rear hold down. Adjust hold down tight
against auger flighting. Retighten bolts. Loosen
bolts (B) holding front wiper on rear auger, and
slide wiper against flighting so end of auger can
only be raised slightly. Retighten bolts. Loosen
(C) and slide hold down tight against auger
flighting. Retighten bolts. To adjust front auger
wiper, loosen bolts (D) and slide wiper against
flighting of auger so end of auger can only be
raised slightly. Retighten bolts. Check adjust-
ment of wipers and hold downs periodically.
A
B
-14-
Shown here is the plastic guard which protects
the operator from accidentally being exposed to
the bottom beater at the discharge opening during
operation of forage box. Keep this guard in proper
position at all times when operating forage box.
D C
ITEM PART NO. DESCRIPTION
2. S335 Front Clutch Plate
3. S341 Idler-Stop Assembly
4. S337 Handle Lever
5. S332 Drive Belt Set
6. S342 Pulley
7. S339 Handle Mount
8. S343 Shifting Rod
9. 11S19 Sprocket 50B20
10. S340 Tightener Pivot Shaft
11. S338 Handle Lever
12. 4C7 Bearing Flange
13. X85 Bearing Flange Sheared
14. K156 Idler Pulley
15. S458 Input Pulley Shaft
16. 4C8 Bearing
17. S347 Shifter Rod End
18. 23N211 Spring 3/4’’
19. X111 3/8’’ x 1’’ Bolt GR.5
20. BFR320 3/8’’ x 1-3/4’’ Bolt GR.2
21. S352 Internal Star Washer
22. K60 3/8’’ Nut
23. B68 3/8’’ Lockwasher
24. S355 3/8’’ Jam Nut
25. K25 3/8’’ Locknut
26. 16SV91 1/2’’ x 3-1/4’’ Bolt GR.5
27. R11 1/2’’ Top Locknut
28. 5B10 1/4’’ x 1’’ Woodruff Key
29. --- 3/8’’ Setscrew
30. --- 5/16’’ Setscrew
31. A14 3/8’’ Nylock Nut
32. X67 3/8’’ Flatwasher
33. S344 Clutch Rod Slide
34. S348 Spring Bracket
35. S349 Drive Pulley Shaft
36. S438 Clip Pin
37. 4C9 Bearing Lock Collar
38. S345 Spacer (.074)
39. K99 Spacer, 7/8’’
40. BFR335 5/16’’ x 2’’ Expansion Pin
41. K68 1/2’’ Lockwasher
42. X112 Spacer, 9/16’’
43. K106 Spacer, 1/2’’
44. BFR220 Cable Clamp
45. ES4 Thimble
46. ES5 Cable Compression Sleeve
47. S361 Stop Cable Stiffener
48. S358 Emergency Stop Cable
49. S362 Handle Lever Grip
50. S369 Spring 5/8’’
51. ES7 Hair Pin
52. R35 1/2” Lock Washer (As Needed)
53. S135 1/4” x 1-1/4” Square Key
-3 9 -
FIGURE 5
CROSS CONVEYOR CLUTCH - BELT DRIVE