H&S H D TWIN AUGER, Operator'S Manual / Parts Book

Page: 35 / 54

DECAL LOCATION
Your H&S H D Twin Auger Self-Unloading Forage Box was manufactured with operator safety in mind.
Located on the forage box are various decals to aid in operation, and warn of danger or caution areas. Pay
close attention to all the decals on your forage box.
DO NOT REMOVE ANY OF THESE DECALS. IF DECALS ARE LOST, DAMAGED, OR IF
FORAGE BOX IS REPAINTED, REPLACE DECALS. REMEMBER: DECALS ARE FOR
YOUR PROTECTION AND SAFETY.
Listed below are the decals on your H D Twin Auger Self-Unloading Forage Box. These decals may be
ordered individually by part number or by ordering a complete set.
ITEM PART NO. DESCRIPTION
A 1494A (4) Warning - Do Not Operate
AA (3) H&S H D Twin Auger
B 1494K (2) Warning - Do Not Remove Shields
BB 5696E Engage
C 72203A Warning - Help Avoid Injury
CC 5696D Disengage
D 1494B Warning - Do Not Remove Shields
DD 093020 Grease Gun
E 5896B Danger - Rotating Driveline
EE 093366 Manual Holder
F Serial Number
G 1-1-91 Beater Engage/Disengage
H 1494P Danger - Stay Clear - Power Lines
I Weasler Danger - PTO (H&S Decal 1494L)
J 1494H (3) Danger - Stay Clear
K 104-3185 Push This Panel
L 5896C Warning - Emergency Stop Reset
M 103-3185 Emergency Stop
N 7+4 3185G Instruction-Entering Forage Box
O 120-2177 (2) Pull To Stop
Q (2) H&S Metal Sign (12’’x24’’)
R 1494C (4) Warning - Moving Parts Under
S (3) Red Reflector
T (5) Amber Reflector
U B17 H&S Decal (8-1/2’’x17’’)
V 1494F Danger - Entering Forage Box
W 7+4-2191 Clean Out
X H&S Patent Numbers
Y FEMA
Z 2495 Warning - Keep Children Away
2699 H D TA Complete Set of Decals
Paint - H & S Red
ZX21 Gallon
ZX22 Quart
ZX23 Pint
-20-
ITEM PART NO. DESCRIPTION
1. F73 Snap Ring
2. F16 Lock Collar
3. F114 Bearing Flange w/Zerk
4. F115 Bearing Greaseable Type
5. F14 Bearing Flange
6. S23 LH Beater Stub Shaft
7. S24 RH Beater Stub Shaft
8. S25 Beater
9. G23 5/16’’ x 1-3/8’’ Square Key
10. F114A Bearing Flange w/Zerk 45 Degree
11. S218 3/8’’ Spacer
12. S26 3rd Beater Sprocket 20T
13. S219 1/4’’ Spacer
14. K60 Nut
15. X67 Washer
16. S27 Wood Chain Tightener
17. S28 Carriage Bolt
18. X58 2nd to 3rd Beater Chain 89 Pitches #50
19. S30 2nd Beater Sprocket 30T - 13T
20. S31 1st to 2nd Beater Chain 98 Pitches #50
21. X58 Beater Drive Chain 89 Pitches #50
22. 10R32 Snap Ring
23. S33 Chain Tightener Bushing
24. S34 Tightener Sprocket w/Bushing
25. L10R35 Chain Tightener Bracket
26. S36 Drive Shaft Spacer
27. S37 Apron Drive Shaft Sprocket
28. S436 3/8’’ x 1-1/2’’ Square Key
29. S327 Poly Gearbox Washer
30. S38 3/8’’ x 2-3/8’’ Square Key
31. ST10 Apron Drive Chain 56 Pitches #80
32. S40 Chain Tightener
33. S41 Bushing
34. S42 1st Beater Sprocket 60T-20T
35. S43 Drive Shaft Brace
36. S44 Bushing
37. S45 Apron Drive Sprocket 30T
ITEM PART NO. DESCRIPTION
38. S46 Grease Line Bracket
39. S47 Grease Line Fitting
40. S48 Short Grease Line
41. S49 Long Grease Line
42. S50 Drive Shaft Bushing
43. S51 LH Drive Shaft Bracket
44. S52 RH Drive Shaft Bracket
45. S53 Center Bearing Bracket
46. S54 T-Rod Slat w/Att. Links
S233 667H Pintle Slat w/Att. Links
47. S55 T-Rod Standard Link
48. S56 T-Rod Connector Link
11S51 667H Pintle Connector Link
11S50 667H Pintle Att. Link RH or LH
49. S57 T-Rod Complete Apron 14’ Box
S230 667H Pintle Apron 14’
S58 T-Rod Complete Apron 16’ Box
S231 667H Pintle Apron 16’
S59 T-Rod Complete Apron 18’ Box
S232 667H Pintle Apron 18’
50. S60 Rear Idler Sprocket
51. S61 Idler Shaft Spacer
52. S62 LH Rear Idler Bracket
53. A7 Tightener Bolt
54. S63 Rear Idler Shaft
55. S64 Center Idler Bracket
56. S65 RH Rear Idler Bracket
57. ST11 Worm Gear Shaft Sprocket 13T
S66 Slow Down Sprocket 11T
58. S67 Grease Line Clip
59. S68 Main Apron Drive Shaft
60. S216 Chain Tightener Assembly
61. S371 Cable Bracket
- 33 -
NOT SHOWN
F157 #80 Connector Link
F158 #80 Offset Link
X60 #50 Offset Link
X61 #50 Connector Link
FIGURE 2
BEATERS AND MAIN APRON DRIVE