background image

USING RANGER

HANDSFREEFARM.COM

10

Setting Up RANGER

RANGER includes several settings that enable you to tailor your system to your needs. Review the following 
sections to quickly set up RANGER for your field.

• “Settings Overview” (below) - shows all the settings in a single map and describes the buttons you use to 

access the menu, navigate the menu, and change/view settings

• “Setup Menu” on page 11 - describes items on the Setup menu
• “Service Menu” on page 12 - describes items on the Service menu

Settings Overview

The map at right shows all available 
RANGER settings. The map enables you 
to quickly identify what settings are 
available and where they are in the menu 
system.

Use the map in conjunction with the button 
descriptions below to quickly change any 
applicable settings.

Button

Purpose

• Press MENU to initially display the Setup menu (top menu in figure above).
• When on the Setup menu, press MENU to exit the menu system.
• When on the Diagnostics or Service menu, press MENU to return to the Setup menu.
• When editing Swath Width, press MENU to move one numerical place to the left (see Swath 

Width below). For example, if the tens place is the current editable value, press MENU to 
move to the hundreds place.

• Use the arrows to move down or up the list of menu items. The selected menu item is 

preceded by ‘>’.

• When editing Swath Width, press the arrows to decrease (down arrow) or increase (up arrow) 

the current number place (such as hundreds or tenths).

• Press ENTER make a setting editable, then, after using the arrows to select a value, press 

ENTER to confirm the selection.

• When editing Swath Width, press ENTER to move one numerical place to the right. When the 

rightmost place is editable, press ENTER to confirm the value and return to the Setup menu.

Setup Menu

Brightness

5

Swath Width

30.00

Sensitivity

Medium

Perimeter Setup

Right

Diagnostics

>

Service Menu

>

Diagnostics

Correction Type

SBAS

Sats

Trk=10, Use in Calc=09

STDEV

0.04 ft

HDOP

1.20

Diff Age

0001 secs

Bit Rate Error

0-0

GPS Software

Ver. 6.8

App Software

Ver. 1.0

Serial Number

300556

Memory

29.87 hr./98% Free

Service Menu

Correction Type

SBAS

SBAS Satellite

AUTO

NMEA Port Setup

>

Unit of Measure

Feet

Language

English

Reset Defaults

>

NMEA Port Setup

NMEA Port Baud

4800

GGA

1 Hz

GLL

Off

VTG

1 Hz

RMC

Off

GSA

Off

ZDA

Off

*

*

The Diagnostics menu is 
read-only (you cannot change 
any Diagnostics values).

Summary of Contents for RANGER

























Reviews: