Handicare PUMA KINETIC Service Manual Download Page 26

Page: 26 / 99

Adjustment options

Version 2011v1

2.12.1 Adjusting the height of the controller 'DX'

•

See fig. 010513020.

The controller can be adjusted in height as follows:

•

Loosen setscrew (A) a few turns with an Allen key
with a key width of 3 mm.

•

Adjust the controller (B) with its swing mechanism to
the desired height.

•

Tighten the setscrew again.

EBAXXX-010513020.en.doc

2.13

Safety belt (option)

•

See fig. 010515000

It is possible to equip the wheelchair with a safety belt.
The safety belt gives extra sitting stability during normal use.
Ask your dealer for information.

For the assembly of the safety belt do the following:

•

Fasten the belt buckle (A) with the aid of a bolt plus
nut.

EBAPUM-010515000.nl.doc

010513020

010515000

Summary of Contents for PUMA KINETIC




































































































Search results

Summary of Contents for PUMA KINETIC

Reviews:

Related manuals for PUMA KINETIC

Brands by name

Popular brands

Handicare PUMA KINETIC, Service Manual

Search results

Summary of Contents for PUMA KINETIC

Reviews:

Related manuals for PUMA KINETIC

Brands by name

Popular brands