Handicare PUMA KINETIC Service Manual Download Page 17

Page: 17 / 99

Adjustment options

Version 2011v1

2.3

Adjusting the back-support angle

•

See fig. 010503010.

For optimal seating comfort the angle (B) of the backrest can
be adjusted continuously.

The angle of the backrest can be adjusted as follows:

•

Loosen the two Allen bolts (A) on the left side of the
back, under the seat, two turns with an Allen key with
a key width of 4 mm.

•

Adjust the desired back angle (B).

•

Tighten the Allen bolts again.

EBAPUM-010503010.nl.doc

2.4

Adjusting the legrests

•

See fig. 010504000.

Adjustment possibilities of the legrests:
A.  Length.
B.  Width.
C.  Depth.

Legrests also have an optional angle adjustment.

XXXXXXX-010504000.en.doc

2.4.1

Adjusting the length of the lower-legrests

•

See fig. 010504010.

The adjustment of the length (L) of the legrests should be
done as follows:

•

Loosen the set bolt (A) a few turns with an Allen key
with a key width of 4 mm.

•

Adjust the length of the legrest.

•

Tighten the set bolt again.

Make sure that there is sufficient free space
under both footplates to be able to drive the
wheelchair over obstacles, without impacting
the footplates.

XXXXXX-010504010.en.doc

010503010

010504000

010504010

Summary of Contents for PUMA KINETIC




































































































Search results

Summary of Contents for PUMA KINETIC

Reviews:

Related manuals for PUMA KINETIC

Brands by name

Popular brands

Handicare PUMA KINETIC, Service Manual

Search results

Summary of Contents for PUMA KINETIC

Reviews:

Related manuals for PUMA KINETIC

Brands by name

Popular brands