background image

4

1  

|

  Introduction

Handicare Freecurve

3D-view

front view

General

Classic

Power supply: 

 

90 V ~ - 240 V ~

Frequency: 

 

50 / 60 Hz

Current: 

  1 

Amp

Power consumption: 

360 Watt

Max. weight: 

 

125 kg

Max. speed: 

 

0.11 m/sec (variable)

Tips without recharging*: 

10 uninterrupted

Max. angle of inclination: 

61 degrees

Min. stair width Van Gogh: 

690 mm   Classic

    Elegance

    Alliance

Max. rail length: 

 

35 metres

* 6 metre trip, with 125 kg load at an angle of inclination 61°

• 

The Classic chair can be delivered in 3 colours: beige, 

   anthracite and red. The material has leathergrain finish.

• 

The armrest, footrest and seat fold up seperately.

• 

The chair can swivel centric in both directions.

• 

It is possible to ride in a swiveled position.

• 

Powered seat is optional.

• 

The powered and illuminated footrest is optional.

• 

The footrest does not swivel with the seat.

• 

Standard and offset footrest.

• 

The height of the backrest can be increased (35 mm).

• 

The position of the backrest can be adjusted on site to 

   increase the depth of the seat by 50 mm

Summary of Contents for FREECURVE Basic























































































Reviews:

Related manuals for FREECURVE Basic