background image

3800i/3800r User’s Guide

3 - 7

Aimer Beam Delay (Aimer Beam option only)

The Aimer Beam Delay allows a delay time for the operator to aim the reader 
before the standard illumination and decoding starts.  The quickset codes sets 
the time between when the trigger is pulled and when the decode starts to either 
1 or 2 seconds.  During the delay time, the aiming beam appears, but the 
illumination LEDs won’t turn on until the delay time is over.  

User-Specified Aimer Beam Delay

If you want to set your own length for the duration of the delay, scan the bar code 
below, then set the time-out by scanning digits (0 - 4000 ms) from the 

Programming Chart

 inside the back cover of this manual and then scan Save.

Aimer Mode (Aimer Beam option only)

If you are reading codes in applications that exhibit high ambient light, you can 
turn on the aimer beam to assist you in reliably finding and scanning a code.  
Select 

Off if you don’t want to use the aimer beam.

2 seconds

1 second

* Off (no delay)

Delay Duration

Off

* On

Summary of Contents for IMAGETEAM 3800i









































































































































































Reviews: