background image

Tools Required

Phillips screwdriver, straight slot screwdriver, 
step ladder, and wire cutters.

Mounting Options

If there isn't an existing UL listed mounting box, 
then read the following instructions. Disconnect 
the power by removing fuses or turning off 
circuit breakers.

Secure the outlet box directly to the building 
structure. Use appropriate fasteners and building 
materials.  The outlet box and its support must 
be able to fully support the moving weight of the 
fan (at least 50 lbs).  Do not use plastic outlet 
boxes.

Figures 1, 2 and 3 are examples of different 
ways to mount the outlet box.

3. Installing Your Fan 

Outlet box

Outlet box

Figure 1

Figure 2

Outlet box

To hang your fan where there is an existing 
fixture but no ceiling joist, you may need an 
installation hanger bar as shown in Figure 4 
(available at your Hampton Bay Retailer).

Note: You may need a longer downrod to 
maintain proper blade clearance when installing 
on a steep, sloped ceiling.

Figure 4

Figure 3

Angled ceiling
maximum
18° angle 

Provide strong
support

Recessed
outlet box

Hanger 
opening must
be facing up-side 

Summary of Contents for WITHROP 656 413
















Reviews: